what is the binary value of loop back address
- 13 Answers
- 20298 Views
- I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / biswajit biswas, kolkata
Hi Jitendra, Thanks for your loads of questions and querries
and this site is worth reading... Thanks to the developers
of this site. But Jitu bhai I want to make a request to you
please send the questions in full format and recognisable
words with no grammatical mistakes. Because a wrong thing is
always wrong. And there is no value... even a little mistake
can cause a great loss to this effort. Make a revision of
your questions and answers before submitting.
Thanks once again... keep sending your questions and answers.
| Is This Answer Correct ? | 0 Yes | 0 No |
Answer / jienderas snha
hi sahain i mark this one wrong becoz this value was not in
the option
there are numric value and i also donot remamer that value
| Is This Answer Correct ? | 0 Yes | 1 No |
thnx jitender...its me shridh...m working for SG ltd..the situation iz like ths -at a specific time in our company the internet connectivity goes off...v hav two networks in our company...but out of it only one link goes down for 5-10 sec...a fastethernet port becomes down for few sec and automatically becomes Up... Is this occures becoz of Power?? If yes thn y the 2nd network is not affected?? plz tel me jitender how to resolve ths problem? as u sd loop in switch is the primary cause of ths....i wanna know how to resolve it...thnx for ur replys jitender sinha.
CPE is an acronym for which of the following? A.) Customer Premise Equipment B.) Central Processing Engineering C.) Customer Process Equipment D.) Central Processing Equipment
Which three pieces of CDP information about neighbours routers are displayed on your console terminal? (Choose three) A. neighbours router a host name B. the neighbours router a hardware platform C. up to one address for each protocol supported D. up to two addresses for each protocol supported
Which two statements about the store and forward switching method are true? (Choose two) A. Latency remains constant regardless of frame size. B. Latency through the switch varies with frame length. C. The switch receives the complete frame before forwarding it. D. The switch checks the destination address as soon as it receives the header and begins forwarding the fram immediately.
If configuring a Cisco router to connect to a non-Cisco router across a Frame Relay network, which encapsulation type would you select? A.) Q933a B.) ISDN C.) IETF D.) CISCO E.) ANSI
Identify the 2 commands that will display the status and information about interface E0 only? A.) show interface ethernet E0 B.) show interface E0 C.) show E0 D.) show int E0 E.) show interface
HI ALL! RECENTLY I COMPLETED MY MCITP, CCNA COURSE, I AM PLANNING TO DO CCNA CERTIFICATION, ANYBODY PLZ SUGGEST ME HOW MUCH TIME (MONTHS) REQUIRED TO PREPARE FOR CCNA, BOOKS, JOB SCOPE IN INDIA, QUALIFICATION REQUIRED, ANY JOB FOR FRESHERS? YOUR GOOD ADVISE IS HIGHLY APPRECIATED. Reg.Khaleel
How do you get help on a command after you have received the % incomplete command response from a switch CLI? A. type "history" to review the prompt before the error B. enter a question mark to display all the console commands C. type help followed by the command to see command parameters D. reenter the command followed by a question mark to view keywords
What is a back off on an 802.3 networks? A. It is latency in store and forward switching B. It is the time used for token passing from machine to machine C. It is the retransmission delay that is enforced when a collision occurs D. It is the result of two nodes transmitting at the same time. The frames from each transmitting device collide and are damaged
What is ping utility?
Hi all, Kindly can you tell me what is demand ccna voice in field and what is profile of ccna voice.so pl very urgent bcz i am going to join institute
raid can be used in? 1 NT 2 Netware 3 all of above mine answer -NT
CCNA 
