Which three types of connectors are commonly associated
with Cisco's V.35 serial cables? (Choose three.)
0 RJ 11
1 DB 60
2 Winchester 15 pin
3 DB 9
4 smart serial
5 RJ 45

Answers were Sorted based on User's Feedback



Which three types of connectors are commonly associated with Cisco's V.35 serial cables? (Cho..

Answer / lunarly

1 DB 60
2 Winchester 15 pin
4 smart serial

Is This Answer Correct ?    25 Yes 1 No

Which three types of connectors are commonly associated with Cisco's V.35 serial cables? (Cho..

Answer / fede

1 DB 60
2 Winchester 15 pin
4 smart serial

Is This Answer Correct ?    4 Yes 0 No

Which three types of connectors are commonly associated with Cisco's V.35 serial cables? (Cho..

Answer / neeraj

01 db60
04 smart srial
05 rj 45

Is This Answer Correct ?    2 Yes 7 No

Which three types of connectors are commonly associated with Cisco's V.35 serial cables? (Cho..

Answer / s.m.feroz ahmed

Hi,

V.35 is a Modem installed on Client location so it requires
the following 3 serial cables

0 RJ11
3 DB 9
5 RJ45

Is This Answer Correct ?    1 Yes 7 No

Which three types of connectors are commonly associated with Cisco's V.35 serial cables? (Cho..

Answer / giuly

db 9
winchester 15 pin
rj45

Is This Answer Correct ?    7 Yes 17 No

Which three types of connectors are commonly associated with Cisco's V.35 serial cables? (Cho..

Answer / jitendera sinha

answer is
rj 11
winchiter 15 pin
and
smart serial

Is This Answer Correct ?    9 Yes 24 No

Post New Answer

More CCNA Interview Questions

Identify the following command to configure a secret password to 'cisco'? A.) Router(config)#enable password cisco secret B.) Router(config)#enable secret cisco C.) Router(config)#enable secret password cisco D.) Router(config)#set secret = cisco

1 Answers  


what are the different asymmetric algorithms?

0 Answers   CCIE,


What is the size of IP address?

0 Answers  


Suppose we are having two Switches i.e. Switch1 & Switch2 Port1 of Switch1 is Connected to Uplink and switch2 is also connected to switch1? So 1>Is there is any loop? 2>How we come to know that there is a loop created? 3>If we add Switch3 to switch2 then there is a possibility of loop Creation?

0 Answers  


Name the command we give on privilege mode for coming back to user execution mode?

0 Answers  






Identify the command to determine if an IP access-list is grouped on interface e0? A.) Router(config)# show ip interface e0 B.) Router> show ip interface e0 C.) Router# show interface e0 D.) Router# show ip interface e0

1 Answers  


what is different between semi-managed and managed Switch ?

2 Answers  


Which command sets IGRP as the routing protocol for autonomous system 100? A. Router(config)#igrp 100 B. Router(config)#network 100 C. Router(config)#router igrp 100 D. Router(config)#enable igrp 100

1 Answers  


Which of the following statements are true? A.) Store and forward switching creates variable latency through the switch B.) Cut through switching creates variables latency through the switch C.) Cut through switching works at wire speed D.) Store and forward switching works at wire speed

2 Answers  


Which OSI layer incorporates the MAC address and the LLC? A.) Data link B.) Network C.) Physcial D.) Transport

4 Answers  


HI friends. i need a suggestion and looking towards you foryours valuable suggestion friends i have completed ccna now i want to done red het linux system admnistration and networking i am liitle bit confuse betwwen them which one is better for me for job point of view reply soon waiting for your reply

1 Answers  


What is NOT a characteristic of a network segment on a switch? A. The segment has its own collision domain B. The segment can translate from one media to a different media C. All devices in the segment are part of the same broadcast domain D. One device per segment can concurrently send frames to the switch.

2 Answers   jetking,


Categories