Answer / awaneesh

Flange rating basically refers to the amount of pressure
the line/flange can handle.
As per EIL standards, it is available in
150/300/450/600/900/1500/2500 psi. So dividing this figure
by 14.2 , we can get the rating in Kg/cm2.

Answer / dinesh puri

Basically, It is Pressure rating for which Flanges can
withstand at particular temperature. There are different
standards specifying Flange rating as ASME/ANSI / PN or DN
and they give the max pressure at particular temp. Flanges
can withstand.

Answer / abhilash rajan

Basically it is showing the amount of pressure it can withstand under non-shock conditions. Pressure will decrease under the temperature increases.


Maximum Allowable non-shock Pressure (psig)
Temperature
(oF) Pressure Class (lb)
150 300 400 600 900 1500 2500
Hydrostatic Test Pressure (psig)
450 1125 1500 2225 3350 5575 9275
-20 to 100 285 740 990 1480 2220 3705 6170
200 260 675 900 1350 2025 3375 5625
300 230 655 875 1315 1970 3280 5470
400 200 635 845 1270 1900 3170 5280
500 170 600 800 1200 1795 2995 4990
600 140 550 730 1095 1640 2735 4560
650 125 535 715 1075 1610 2685 4475
700 110 535 710 1065 1600 2665 4440
750 95 505 670 1010 1510 2520 4200
800 80 410 550 825 1235 2060 3430
850 65 270 355 535 805 1340 2230
900 50 170 230 345 515 860 1430
950 35 105 140 205 310 515 860
1000 20 50 70 105 155 260 430

Answer / atul

it is the capacity of flange to hold pressure at non shock
conditions

What is meant by lmtd?

0 Answers  

---

Explain what does 0.125 inch stand for in 0.125 inch npt thread?

0 Answers  

---

What are your specific job requirements in mechanical engineers?

0 Answers  

---

1. What are good characteristics of good combustion in a boiler? 2. What do you analyze from boiler water analysis? 3. What do you treat in high alkalinity of boiler water? 4. What is a feed water pump? Dearator feed heater? 5. What is the purpose of the nozzle of impulse turbine? 6. What are the things needed to have an efficient boiler burning? 7. Name Of Parts And Each Purpose 8. What are the causes of emergency stop in a steam engine? 9. What is the normal vacuum pressure in a steam turbine atmospheric condenser? What would cause the press to falls? 10. Steam turbine (function an parts) 11. What is the boiling point of water? 12. What are the safety devices of boiler? 13. What is the effect of high alkaline water to a boiler? 14. Steps In starting boilers. 15. Small gear found in the steam turbine. 16. What is an Economizer? 17. What are the methods of heat transfer? 18. Types of pressure 19. What are the different parts of impulse reaction turbine? 20. What is the color of the flame of the boiler running in good condition? 21. What type of pump is commonly used is feed water system in auxiliary boiler? 22. What is the specific heat of water? 23. What do you do to prevent flare black? 24. What is a brake horsepower? 25. What is the purpose of a de-superheater? 26. What is the purpose of corrugated furnaces? 27. What are the causes of steam turbine failure? 28. What is the purpose of superheater? 29. Given a cutaway isometric view of the steam turbine. Examinee was asked to identify the following Parts: 30. What is thrust bearing? 31. Give five boiler mounting valves. 32. In steam boiler, what are the various test in water boiler? 33. How much calorific value of heat is needed to heat 00c of 34. What will happen if boiler backfires? 35. What is the color of flame if the boiler is running in good condition? How about when it is not in good condition? 36. How does the steam work in a steam turbine? 37. What are the causes of boiler backfire and steps in how to prevent it from happening? 38. What are the causes of high alkalinity in boiler water? 39. What are sensible heat, latent heat, and specific heat of water? 40. What are the causes of turbine vibration 41. Identify the parts of steam turbine 42. What is the normal Ph value of boiler water 43. Causes of dilution of lubricating oil in a steam turbine? 44. Explain briefly- good combustion of auxiliary boiler? 45. Method of testing or checking boiler water? 46. What is mean carry over of Aux. Boiler? 47. What are steam turbine parts usually come into damage? 48. Why must we pay attention when we drain steam in steam turbine. What factors are observed? 49. What type of pump use in boiler F.O. system? 50. What parameters to be reported when we send lubricating oil for shore analysis? 51. In boiler, what does steam and smoke goes out to the funnel. What reason? 52. Where can you find the feed check valve and feed stop valve and give the purpose of it? 53. What are the causes of troubles in boiler during operations? 54. Give the purpose of nozzle in impulse turbine? 55. What s gland sealing steam? 56. How to prevent back fire of boiler? 57. What is the used of economizer in boiler? 58. What is the seal packing gland for turbine? 59. What is the flow of steam in an impulse turbine? 60. What will happen if you blow the soot in the boiler? 61. State the purpose of air heater? 62. How to operate soot blower boiler and economizer? 63. What do you mean by A.CC.? 64. What is the thermal efficiency of a diesel engine? 65. What is a blow down valves?

0 Answers   CSPDCL-Chhattisgarh State Power Distribution Company Limited, RRB,

---

15. What is the difference between first angle projection and third angle projection?

2 Answers   Amul,

---

why eta(η) became the symbol of Newton law of viscocity

0 Answers  

---

Explain how the lubricating oil circulates in a diesel engine.

0 Answers   RRB,

---

dear sir i m anshul kumar from dehradun i want to last five year railway chandigarh and allahabd entrance exam papers pls send it on my id my id is anshuldhiman83@gmail.com or anshuldhiman@rediffmail.com i shall be very greatful to u thank u

0 Answers  

---

What is brain of the computer?

0 Answers  

---

what is the effect of throttle pressure on turbine efficiency?

0 Answers  

---

A diesel engine,if i use there petrol fuel,What is problem there & what is the result?

6 Answers   TATA, Tata Steel Limited,

---

written test: 1) periodical and monthly maintenance are called preventive or panned maintenance. 2) Mechanical seal parts and their material. 3)Urea plant main parts and their construction material details.4)Name diagram of the given turbine5) Turbine nomenclature like API name.6)All types of corrosion like Galvanic and oxide with example.7)Parts of gate valve and its usage. diaphragm gate valve usage. etc.....

0 Answers   QAFCO,

---