Identify the mode reflected by the following prompt 'Router'? A.) Setup B.) RXBoot C.) Boot mode D.) Privileged exec mode

1 Answers  

---

What are the steps of conversion for data encapsulation?

0 Answers  

---

What is the command use to add a banner to a cisco router configuration?

0 Answers  

---

Q: why are switch trunking modes ( dynamic auto , dynamic desirable )used in switch while trunking? if only negotiation is the factor it can be done with one mode as well ie dynamic desirable . but why we need dynamic auto. coz it dsnt negotiates ..at all please post answer asap thanks :

2 Answers  

---

What is BGP attribute & How many types of attributes are used by BGP???

5 Answers   Hathway, HCL, Infinite Computer Solutions,

---

Identify the components in the following command 'interface serial0/1/1' A.) Serial interface, port number 0, slot 1, port adapter 1 B.) Serial interface, slot 1, port number 1, port adapter 0 C.) Serial interface, slot 0, port adapter 1, port number 1

2 Answers  

---

Identify 2 PPP characteristics? A.) Is proprietary to Cisco B.) Supports authentication C.) Support compression D.) Run on a multi-access network

3 Answers  

---

What does a Standard IP Access-list use as test criteria? A.) IP source address B.) IP source and destination address, protocol numbers and port numbers C.) IPX source and destination address D.) Source MAC address

2 Answers  

---

You want to segment a network. The network is running SNA and Netbios. Which device should NOT be used to segment the network? A.) A store and forward switch. B.) A router. C.) A Catalyst 5000. D.) A cut-through switch. E.) A bridge.

1 Answers  

---

take a pen and copy before solving that question there is a router name Ra there is two switch sw1 and sw2 sw1 is coneceted through fa0/1 interface of router Ra sw2 is conected through the fa1/1 serai interface of router s0/1 conected through the isp with it ip address 192.168.1.1 now therer are three host conexted through the sw1 and having ip host1=10.1.2.1 host2=10.1.2.2 host3=10.1.2.3 now there is also 3ree host conected through switch 2 i.e sw2 having ip host4=10.1.1.1 host 5=10.1.1.2 host 6=10.1.1.3 now i think u have made corect confrigation.now questios is started network admin configure the Ra router in that fassion Ra(config)#access-list 2 permit 10.1.1.0 0.0.0.255 Ra(config)#line vty 0 4 ra(config)#access-class 2 in now question is that why should network admnistratoe do it in this maneer A to give access sw1 host to acess internet B to prevent sw1 host from acessing comand promt c to prevent sw2 host from accessing console of router ra D to give sw2 host access to the enternet e prevent sw1 host from accessing internet f to prevent sw1 host from acessing the sw2 host network isp------(s0/1)..RA..(fa1/1)---SW2-host (4,5,6) | | (sw1)------host 1,2,3 this is not exect digarm but help to derive the diagram plz answer as soon as possible

6 Answers   AT&T,

---

The Internet Protocol (IP) occurs at what layer of the seven layer model? A.) Physical B.) Presentation C.) Network D.) Datalink E.) Session F.) Transport

3 Answers  

---

The two sublayers of the IEEE Data Link Layer are which of the following? A.) Link and Logical Control B.) Data Link and LLC C.) Logical Link Control and Media Access Control D.) Data Link and MAC

3 Answers  

---