ENGINEERING MATERIAL - EXAMPLE 12.1 : In crystal material, hexagonal crystal sys

ENGINEERING MATERIAL - EXAMPLE 12.1 : In crystal material, hexagonal crystal system could form 4-digit index in certain direction of solid. For [1(-1)0] direction in the hexagonal crystal systems of particular catalyst applied in fume removal of incinerator, what is the four-digit index for this direction? Hint : The transformation equations between the 3-digit [h'k'l'] and the 4-digit [hkil] indices are : h = (1/3) (2h'-k'); i = - (h + k); k = (1/3) (2k'-h'); l = l' A. [(-1)100] B. [1(-1)00] C. [(-1)000] D. [00(-1)(-1)] E. [(-1)0(-1)0]

Question Posted / kangchuentat

1 Answers
2329 Views
I also Faced
E-Mail Answers

ENGINEERING MATERIAL - EXAMPLE 12.1 : In crystal material, hexagonal crystal system could form 4-dig..

Answer / kangchuentat

ENGINEERING MATERIAL - ANSWER 12.1 : h = (1/3) [ 2 - (-1) ] = 1; k = (1/3) ( - 2 - 1 ) = -1; i = - ( 1 - 1 ) = 0; l = i = 0. Solution is [1(-1)00]. Answer is B. The answer is given by Kang Chuen Tat; PO Box 6263, Dandenong, Victoria VIC 3175, Australia; SMS +61405421706; chuentat@hotmail.com; http://kangchuentat.wordpress.com.

Is This Answer Correct ?

0 Yes

0 No

Post New Answer

More Chemical Engineering Interview Questions

Why is post-weld heat treatment (stress relieving) sometimes necessary for welded vessels?

0 Answers

CHEMICAL ENERGY BALANCE - EXAMPLE 11.1 : Please match the term A - E with the stated definition i - v. Terms : A. Yield. B. Selectivity. C. Relative saturation. D. Molal saturation. E. Absolute saturation. Definitions : i. (moles of desired product formed) / (moles that would have been formed if there were no side reactions and the limiting reactant has reacted completely); ii. (moles of desired product formed) / (moles of undesired product formed); iii. (relative humidity 40 % means partial pressure of water vapour equals 4 / 10 of the vapour pressure of water at the system temperature); iv. (moles of vapour) / (moles of vapour dry gas); v. (mass of vapour) / (mass of dry gas).

1 Answers

Define "good" cooling tower water?

0 Answers

Explain the use of gear pumps in motor?

0 Answers

Are there any special considerations to be taken into account for combustion ammonia?

0 Answers

Why reflux is necessary in distillation column?

1 Answers Deepak Fertilisers,

Are there any general rules that should be considered when designing a slurry piping system?

0 Answers

When should one be concerned with the tube wall temperature on the cooling waterside of a shell and tube exchanger?

0 Answers

when liquid stored in spherical vessel,equilibrium shift towards liquid.what is the benefit of it?

1 Answers

A cantilever beam of length L = 3 m carries a uniformly distributed load (UDL) of W = 20 N / m throughout the length. Calculate the bending moment, BM of the beam near the fixed end. What is the shear force, SF at this point? Let SF = -WL, BM = -LWL/2.

1 Answers

what are the precautions u are taking while starting HT motors?

2 Answers HPCL, MRPL Mangalore Refinery and Petrochemicals Limited,

Question 111 - There are 6 spin orbitals in p subshell in a ground state carbon atom. Only 2 electrons fill the p subshell. Number of different ways for n electrons to occupy the k spin orbitals are k! / [ (n!) (k-n)! ]. Find the number of different configurations of electrons to occupy the p subshell in a carbon atom.

1 Answers

For more Chemical Engineering Interview Questions Click Here