Why 11KV/440V distribution supply use for Domestic use?

3 Answers   Essar, Getco, Nissan,

---

i want use the cable size 16cx4 core aluminium usege watts 240x2000w this cable size is correct?

0 Answers   Sabre,

---

Is it necessary to place tap changer in secondary winding or we can use on both sides?

3 Answers  

---

For electrical designers what are the standard should know? i want learn about this standards. how to get information/reference. anybody help in this regards please.

0 Answers  

---

In both 600/1000 V cable and 450/750 V cable, we can supply 415 V. However for distribution, all utilities are using only 600/100 V instead of 450/750 V. What is the reason?

0 Answers  

---

what is the difference between induction and synchronous motor?explain in simple words?why 3 phase motor is given preference over single phase motor.

10 Answers  

---

what is difference between electrical and electronics

2 Answers  

---

What is the d/f between DOL & star delta starter & automatic star delta starter?

23 Answers   ACC, Dalkia, Engineering, Indeco, NINL, Novotel, RMH Control Systems, Wipro,

---

TRAFO 1. WHY BREATHER IS USED. 2. WHY OIL GOES DOWN IN CONSERVATOR TANK. 3. WHY WE ARE TAKING OIL SAMPLE TAKING FROM BOTTOM OF TRANSFORMER. 4. HOW TO CHECK IR VALUE OF TRANSFORMER. 5. WHY OLTC HAVING BUCHHOLZ TRIP ONLY; WHY NO ALARM. 6. OFF LOAD TAP CHANGER OPERATION PROCEDURE. 7. TR. SHUTDOWN / ISOLATION PROCEDURE. 8. WHEN THREE TRS. IN PARALLEL, ONE TR. IS NOT SHARING THE LOAD – WHAT IS REASON AND WHAT YOU WILL DO. 9. WHY TR. HAS OLTC IN HV SIDE. 10. WHAT IS % IMPEDANCE. 11. WHY TR. RATING IN MVA. 12. WHAT IS VECTOR GROUP IN TR. 13. CONDITION FOR PARALLEL OPERATION OF TRS. 14. WHAT IS TERTIARY WINDING. WHERE IT WILL BE. 15. IF TR. TRIP ON BUCHHOLZ OR TAP CHANGER RELAY, WHAT YOU WILL DO. 16. DIFFERENCE BETWEEN OIL TEMP. AND WINDING TEMP. PROTECTION 17. HOW WINDING TEMP. IS MEASURED IN CAST RESIN TR. 18. DIFFERENT TYPES OF FAULTS IN TR. Trafo - Page-1 of 2 19. WHAT HAPPENS WHEN TR. CHARGED FROM LV. 20. WHAT WILL YOU DO IF MEGGER READING SHOWS ZERO BETWEEN LV WINDING AND EARTH. 21. CAN WE INTERCHANGE BUCHHOLZ RELAY OF MAIN TANK AND OLTC TANK. 22. IF THE LINE BETWEEN BREATHER AND CONSERVATOR TANK 23. LOCKED, WHAT WILL HAPPEN DURING LOAD CYCLE. 24. WHAT IS THE FUNCTION OF OIL SEAL IN BREATHER. 25. WHAT ARE LOCATIONS FOR BUCHHOLZ RELAY FIXED IN POWER TR. 26. WHAT ARE CHECKS IN POWER TR. DURING MAINTENANCE. 27. WHAT IS IMPORTANT WHEN WE CHECK OLTC OPERATION DURING MAINTENANCE. Trafo - Page 2 of 2

0 Answers   KSEB,

---

How to connected to energy meter, pt, ct, ammeter, voltmeter and selector switch.

1 Answers   Omplas,

---

what are the functions & ratings of panels mentioned below: 1. Main LT Panel(MLTP) 2. Motor Control Centre(MCC) 3.Feeder pillars 4.Busducts

1 Answers   Aurobindo,

---

What is the maximum advisable distance where it is required to interconnect a 500 KVA 480 V 3 ph transformer and the main panel or MCC ignoring the voltage droop affectation, does it is exist any standard about it?

2 Answers  

---