Answer / pijush mondal

R#show ip ospf interface brief

Which command would configure Interface E0 with an IP address of 12.23.4.5 using a Subnet mask of 255.255.255.0 ? A.) ip address 12.23.4.5 255.255.255.0 B.) ip address 12.23.4.5 /24 C.) ip address 12.23.4.5 mask 255.255.255.0 D.) ip address 12.23.4.5 mask ff:ff:ff:0 E.) that is an invalid mask for a class 'A' address

3 Answers   Wipro,

---

Which command displays the IP addresses assigned to specific host names? A. show hosts B. show interface C. ping host name D. config host name E. show host mapping F. show host ip address G. trace ip addresses host name H. a partridge in a pear tree

2 Answers  

---

When you cords an IP address on a place router which command stale the IP processing on the interface? A. ip enable B. network ip-address C. ip address ip-address subnet mask D. the exit command from the enabled configuration E. copy running-configuration to startup-configuration

3 Answers  

---

On an ISDN BRI interface, the control channel is the 'D' channel. What is the rate of this channel? A.) 64 Kbps B.) 1.544 Mbps C.) 128 Kbps D.) 2.048 Mbps E.) 16 Kbps

4 Answers  

---

hi friend i am stuck in the big problem.this problem is regading pix firewall. i have a cisco pix 515e firewall inmy company.now when i configure it and after rebooting it the ACT link never getup.when i apply clear config all comand the ACT link get up after oveservation i see that there is fauilover problem when i apply failover active ACT link agin get up is there any way to get my firewall in standby mode rember that there is only on firewall within my n/w i am lookig towards all of you jitendera kumar sinha

0 Answers  

---

---

Which is the protocol using multiple tcp/ip connections? SLIP or PPP

2 Answers   Sutherland,

---

Which command will give the following output: Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int * 0 CTY - - - - - 0 0 0/0 - 1 AUX 9600/9600 - - - - - 0 0 0/0 - * 2 VTY - - - - - 2 0 0/0 - 3 VTY - - - - - 0 0 0/0 - 4 VTY - - - - - 0 0 0/0 - 5 VTY - - - - - 0 0 0/0 - 6 VTY - - - - - 0 0 0/0 -

1 Answers  

---

The Datalink Layer is broken down into 2 layers, LLC and MAC. The LLC establishes media independence and what else? A.) Provides Windowing. B.) Provides flow control. C.) Provides SAP's (Service Access Points). D.) The Datalink layer does not have sublayers. E.) Provides SAP's (Service Advertising Protocol). F.) RIP Updates.

2 Answers  

---

What is a characteristic of Store and Forward switches? A.) They work at wire speed. B.) They are the same as Cut-Through switching in 'prune' mode. C.) They forward based on transport layer info. D.) They forward the frame before it is completely read. E.) They increase latency.

1 Answers  

---

plz send me cisco contact no india?

0 Answers   3i Infotech, Cisco,

---

What are the differnt memory use in cisco router?

0 Answers  

---

what is LAPB

2 Answers   ASD Lab,

---