Answer / jitendera

Friends this is Going to be a lenthy post hence i am keeping
it vey short

my one of the Friend mr. Shahin ( CCNA,CCNP,CCIE (Routing))
has created a Blog i will request him to update his Blog
with detail
i am going to send him one mail and going to call him if he
can update his blog with the Answers

==============================================================
Answer-:

process of ARP and RARP
ok let Suppose that there is switch and two pc are
Connected let say pc1 have the ip 1.1.1.2/24 with mac A and
pc2 have ip 1.1.1.3/24 with mac B

now pc1 want to communicate hence what will be the process

Pc1 will send the data with

1) source ip address
2) source mac address
2) destination ip address
4) destination mac address ==unknown hence it will be
replaced by Mac ff:ff:ff:ff:ff:ff( this Amc is Know as
Broadcast mac)

now Switch receive that data and he make the arp entry for
source and for destination

But here the arp entry for the source will be correct but
arp entry of the destination will be destination ip address
and mac address ff:ff:ff:ff:ff:ff.

Now Switch broadcast this data and it will ask Hey are you
have ip address 1.1.1.3 Pc2 reply yes yes i have

once he reply he will Replace the MAc wff:ff:ff:ff:ff:ff
with his own mac

Now Swicth know that ip address 1.1.1.3 have mac B and he
will correct the ARP table inside it

That is the ARP process

Answer / jitendera

Complicated as the process is is lengthy Wait for my next
update i will Answer it

When you cords an IP address on a place router which command stale the IP processing on the interface? A. ip enable B. network ip-address C. ip address ip-address subnet mask D. the exit command from the enabled configuration E. copy running-configuration to startup-configuration

3 Answers  

---

Which ISDN protocol prefix specifies switching and signalling? A.) I B.) E C.) Q D.) S

1 Answers  

---

IPX routing updates occur how often? A.) Every 30 seconds B.) Every 60 seconds C.) Only as needed D.) When the remote router asks for an update

1 Answers  

---

Identify 3 characteristics of IP RIP? A.) Distance vector B.) Administrative distance is 120 C.) Periodic updates every 60 seconds D.) Uses a composite metric E.) Can load balance

1 Answers  

---

Identify the default IPX serial encapsulation? A.) Novell-Ether B.) SDLC C.) SNAP D.) HDLC

1 Answers  

---

Hi all, Sorry, but i want to say that right now i have around two years experience and doing the job as a network engineer(ccna certified).but i want switch job so please can tell me any opportunity.

1 Answers   Wipro,

---

Identify the command mode necessary to enter the extended ping command? A.) Router# B.) Router> C.) Router(config)# D.) Router(ext-ping)#

1 Answers  

---

Which of the following is an invalid host address using a netmask of 255.255.255.192? A.) 10.1.1.1 B.) 10.1.1.66 C.) 10.1.1.130 D.) 10.1.1.127

3 Answers  

---

What is the protocol number for TCP? A.) 80 B.) 21 C.) 11 D.) 6

3 Answers  

---

What is the different between console port and auxiliary port?

0 Answers  

---

Identify 2 features of PPP PAP authentication? A.) Username and password is sent in clear text B.) Authentication messages are sent periodically during the connection C.) More secure than CHAP D.) Remote node is control of authentication process

1 Answers  

---

What does the IPX maximum-path command do? A.) Allows you to disable the TTL on an IPX packet B.) This parameter is only used in NLSP routing C.) Sets the maximum metric that can appear in the routing table D.) Configures round robin load sharing over multiple equal metric paths (parallel paths)

1 Answers  

---