Answer / abdul hameed

In general:
Centrifugal pumps are Flow oriented.
Positive displacement pumps are Pressure oriented.

Answer / jsjhala

if we require a high pressure and low volume flow rate
than we can use positive displacement(because on that a
simple piston cylinder arrangement are taken so we seeing
less amount of leakage problem)and on centrifugal pump ,its
works on the principle of centrifugal action and its
application on that case if we required high volume flow
rate with less pressure

Answer / rohit kumar jha

Centrifugal pump is a negative displacement pump. A Positive
displacement pump is a pump where there is no any( could be
very less) back flow of fluid.
But in the case of the centrifugal pump the back flow is
indeterminate, which is termed to be as NEGATIVE displacement
pump.

Answer / dr. muhammed mohsin khan

Centrifugal pumps are negative /dynamic/non positive type pump in which flow energy is first get converted into thev kinetic energy(velocity energy)and finally converted into the pressure energy these are flow oriented pumps whereas positie displacment pumps are pressure oriented as well as volue is directed converted into the pressure there is no leakage if assumed where as in centrifugal pump back flow is always there

Answer / abhi

positive displacement pump will transfer equal amount of fluid during each suction but centrifugal will not.

Answer / amrit

there are two types of pumps. positive and dynamic
displacement pump. in a pump if there is time gap between
suction and discharge that means there is no continous
flow of transfering liquid then the pump is posittive. and
if in a pump there is a continous tranfering of liquide
from suction to dischrage without any pulsating flow then
the pump is dynamic. A positive displacement pump is an
impuls machine , where as dynamic pumps are Reactin machine.

hello i have a problem !!!! i am studying gait analysis"human walking; and i had only single camera"sony 25 frames/s" and 2 separated force plates, and there is no synchronization between the camera and the force plates!. i wrote a matlab program to calculate joints moment(sagital) using inverse dynamics methode. and there is a problem with the output data!! can you help me.

0 Answers  

Explain what are the thermal conductivity properties of brass?

0 Answers  

What happens when too much cylinder oil is injected in the working cylinder?

0 Answers  

what is routh,s law in thermal engineering ?

0 Answers   TATA,

If Seller is Registered with Karnatka State and Selling the Engg. goods to Delhi based non registered company, then what is the CST they charge?

0 Answers  

1. What are good characteristics of good combustion in a boiler? 2. What do you analyze from boiler water analysis? 3. What do you treat in high alkalinity of boiler water? 4. What is a feed water pump? Dearator feed heater? 5. What is the purpose of the nozzle of impulse turbine? 6. What are the things needed to have an efficient boiler burning? 7. Name Of Parts And Each Purpose 8. What are the causes of emergency stop in a steam engine? 9. What is the normal vacuum pressure in a steam turbine atmospheric condenser? What would cause the press to falls? 10. Steam turbine (function an parts) 11. What is the boiling point of water? 12. What are the safety devices of boiler? 13. What is the effect of high alkaline water to a boiler? 14. Steps In starting boilers. 15. Small gear found in the steam turbine. 16. What is an Economizer? 17. What are the methods of heat transfer? 18. Types of pressure 19. What are the different parts of impulse reaction turbine? 20. What is the color of the flame of the boiler running in good condition? 21. What type of pump is commonly used is feed water system in auxiliary boiler? 22. What is the specific heat of water? 23. What do you do to prevent flare black? 24. What is a brake horsepower? 25. What is the purpose of a de-superheater? 26. What is the purpose of corrugated furnaces? 27. What are the causes of steam turbine failure? 28. What is the purpose of superheater? 29. Given a cutaway isometric view of the steam turbine. Examinee was asked to identify the following Parts: 30. What is thrust bearing? 31. Give five boiler mounting valves. 32. In steam boiler, what are the various test in water boiler? 33. How much calorific value of heat is needed to heat 00c of 34. What will happen if boiler backfires? 35. What is the color of flame if the boiler is running in good condition? How about when it is not in good condition? 36. How does the steam work in a steam turbine? 37. What are the causes of boiler backfire and steps in how to prevent it from happening? 38. What are the causes of high alkalinity in boiler water? 39. What are sensible heat, latent heat, and specific heat of water? 40. What are the causes of turbine vibration 41. Identify the parts of steam turbine 42. What is the normal Ph value of boiler water 43. Causes of dilution of lubricating oil in a steam turbine? 44. Explain briefly- good combustion of auxiliary boiler? 45. Method of testing or checking boiler water? 46. What is mean carry over of Aux. Boiler? 47. What are steam turbine parts usually come into damage? 48. Why must we pay attention when we drain steam in steam turbine. What factors are observed? 49. What type of pump use in boiler F.O. system? 50. What parameters to be reported when we send lubricating oil for shore analysis? 51. In boiler, what does steam and smoke goes out to the funnel. What reason? 52. Where can you find the feed check valve and feed stop valve and give the purpose of it? 53. What are the causes of troubles in boiler during operations? 54. Give the purpose of nozzle in impulse turbine? 55. What s gland sealing steam? 56. How to prevent back fire of boiler? 57. What is the used of economizer in boiler? 58. What is the seal packing gland for turbine? 59. What is the flow of steam in an impulse turbine? 60. What will happen if you blow the soot in the boiler? 61. State the purpose of air heater? 62. How to operate soot blower boiler and economizer? 63. What do you mean by A.CC.? 64. What is the thermal efficiency of a diesel engine? 65. What is a blow down valves?

0 Answers   CSPDCL-Chhattisgarh State Power Distribution Company Limited, RRB,

interviw tips for bhel supervisor trainee

0 Answers   GIL, Jindal Steel and Power,

• Could you describe a typical day or week in this position? What are the challenges facing this position?

1 Answers  

can we say all tapered pipes as nozzle?

8 Answers  

DEAR SIR, I NEED A MODEL QUESTION PAPER OF JSPL. i'M IN mechanical BRANCH. E-MAIL ID:sksuman289@gmail.com

0 Answers  

What do you mean by cotter joint?

0 Answers  

What is the profile of QA engineer

0 Answers   MAHINDRA,