Wat is the best to use in a generator a 6.5kva or a 7 kw

Question Posted / andries

4 Answers
11670 Views
I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

Wat is the best to use in a generator a 6.5kva or a 7 kw..

Hi Jaswinder, the DGs are designed based on the load dependency only. If you are bring the DG in higher rating for low load then no meaning of efficiency.

Hence, 6.5 KVA or 7 KW(8.75 KVA) are doesn't matter. It is fully depends on the magnitude of load.

ersaravananp@gmail.com

Is This Answer Correct ?

5 Yes

0 No

Wat is the best to use in a generator a 6.5kva or a 7 kw..

Answer / saravanan.p

Generator ratings are always noted in KVA, not in KW. The ratings are designed based on the load dependency.

From your question,6.5 KVA is better than 7 KW(8.75KVA Aprox.)

ersaravananp@gmail.com

Is This Answer Correct ?

3 Yes

1 No

Wat is the best to use in a generator a 6.5kva or a 7 kw..

Answer / jaswinder singh

I agreed that Generator rating is always noted in KVA. From
the question, 6.5 KVA Generator can run for 5.20 KW only
which less than 7 KW. So 7KW (8.75 KVA) DG set is better.

Is This Answer Correct ?

1 Yes

1 No

Wat is the best to use in a generator a 6.5kva or a 7 kw..

Answer / simon

hiiiiiiiiiiiiiiii

6.5Kva=6500VA(250V*26Amp)IN 1Phase(440V*14.77Amp)in 3Phase
7Kw=7000W(250V*28Amp) in 1Phase (440V*15.9Amp)in 3Phase

Is This Answer Correct ?

0 Yes

0 No

Post New Answer

More Electrical Engineering Interview Questions

if receiving voltage is higher than sending ones what will be the effect of receiver

4 Answers

what are the uses and applications of rectifiers?

3 Answers

Dear Sirs, I am a technical persons.In one of our Electrical Sub- Station, We have installed three numbers of 1250KVA ,11KV/0.415KV Transformer to feed the Factory load. We have found some abnormality. In one of our Transformers the leakeage current from transformer body to earth through earth continuity wire is almost 86 Amp but in other transformer it is (5-10)Amp. where the load current on three phase and neutral are respectively 1360Amp,1400Amp,1370 Amp & 176Amp. So please any technical person help me about the reasons of this situation and how I can rectify the fault. Moreover,I have measured the earth resistance of the Earth continuity wire which is less than 1 Ohm. Thanks Tapas Barua

3 Answers

How to design the blower for motor? how to two blowers connected in motor?

1 Answers Ashok Leyland, TATA,

what happen if generator exitation lost?

7 Answers

Will u plz give me simple diagram for tube light connection & also function of chock?

8 Answers Bhushan Power Steel, Dalmia Group, Jindal, Practical Viva Questions, TCS, Windmoller,

what r the types of detectors? state the location these detectors?

3 Answers

How is the gain affected by the introduction of feedback in a control system.

0 Answers GE,

what is non uniform load

1 Answers

I have done my m.tech in electrical engg discipline. Can any one please suggest me how should I prepare for getting into phd in iit or nit.How should I prepare for getting into lecturership

0 Answers

why do the alternator doesnt have open circuited windings in armature???

1 Answers

Difference between ups and invertor

3 Answers

For more Electrical Engineering Interview Questions Click Here