Golgappa.net | Golgappa.org | BagIndia.net | BodyIndia.Com | CabIndia.net | CarsBikes.net | CarsBikes.org | CashIndia.net | ConsumerIndia.net | CookingIndia.net | DataIndia.net | DealIndia.net | EmailIndia.net | FirstTablet.com | FirstTourist.com | ForsaleIndia.net | IndiaBody.Com | IndiaCab.net | IndiaCash.net | IndiaModel.net | KidForum.net | OfficeIndia.net | PaysIndia.com | RestaurantIndia.net | RestaurantsIndia.net | SaleForum.net | SellForum.net | SoldIndia.com | StarIndia.net | TomatoCab.com | TomatoCabs.com | TownIndia.com
Interested to Buy Any Domain ? << Click Here >> for more details...


IN POWER PLANTS NORMARLY BOILER DRUMLEVEL TRIPPING GIVEN AT
20% OF WATER BUT WHY NOT THEY GIVE AT 0% OF WATER?

Answers were Sorted based on User's Feedback



IN POWER PLANTS NORMARLY BOILER DRUMLEVEL TRIPPING GIVEN AT 20% OF WATER BUT WHY NOT THEY GIVE AT ..

Answer / venugopal

Because 0% level produced air lock and also oxygen partical
are removed

Is This Answer Correct ?    3 Yes 1 No

IN POWER PLANTS NORMARLY BOILER DRUMLEVEL TRIPPING GIVEN AT 20% OF WATER BUT WHY NOT THEY GIVE AT ..

Answer / mithilesh kumar

hi frnd..
any boiler tripping in two point.1st one is the high and
second is the low limit.
so when boiler tripping at low it's totally protection for
bed coil.if there water is not available then bed coil may
be burst and for high for safety for turbine bcoz this time
water may be reach psh(primary super heater),ssh,and also
in fsh..

Is This Answer Correct ?    1 Yes 0 No

Post New Answer

More Mechanical Engineering Interview Questions

define stress

6 Answers  


How do you reset the circuit breaker?

0 Answers   RRB,


Did you know the provision of fire brigade inlet

0 Answers   Marvel ERP,


What are the different types of fits? Explain

0 Answers   Bechtel,


why we are using mineral wool as insulation material than glass wool , in india?

0 Answers  


What is surging in centrifugal compressor. how its happened and how to avoid it.?

10 Answers  


Define cotter joint?

0 Answers  


why direction of angular acceleration is not find out by right hand rule?

0 Answers  


when a solid shaft is subjected to tension its linear dimension changes equaly as its lateral dimension,then what will be its poissons ratio?

7 Answers   Crompton Greaves,


Dear Sir, Please send me the questions frequently asked during bhel persoal interview for supervisor trainee With worm regards, Alok Kumar Rout e-mail id- rjdalok22@gmail.com

0 Answers  


What motivates you to do a good job?

7 Answers   Maruti Suzuki,


How many 1.5 ton A/Cs can run on 7.5 kw generator (diesel)?

0 Answers  


Categories
  • Civil Engineering Interview Questions Civil Engineering (5086)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4453)
  • Electrical Engineering Interview Questions Electrical Engineering (16638)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1095)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)