Interested to Buy Any Domain ? << Click Here >> for more details...
What should be looked at first to determine if a customer
should switch from a hub environment to a switched environment?
A. Investigate the number of broadcasts
B. Investigate the number of collisions
C. Determine what routing loops are present
D. Determine which switching type is being used by the hubs
- 1 Answers
- 3058 Views
- I also Faced
- E-Mail Answers
Answer / guest
Answer: B
You should investigate the number of collisions to determine
if a customer should switch from a hub environment to a
switched environment. A collision domain is the network area
within which frames that have collided are propagated or
increased. Repeaters and hubs propagate collisions but
switches, bridges, and routers do not. By controlling
collisions, users have more available bandwidth and have
better response time.
| Is This Answer Correct ? | 0 Yes | 0 No |
how many default route can be configure on a router
When characterizing a network, how many buffer misses should not be exceeded on a Cisco router per hour? A. 10 B. 25 C. 50 D. 100
Match the following devices with the correct description. A. Switch 1. Operates at the physical layer and extends the cable as if it is a single cable. B. Router 2. Operates at the physical layer and connects all connections into one device or concentrator. C. Repeater 3. Operates at the network layer and can filter both hardware and network addresses. D. Hub 4. Works at the Data-Link layer and transmits a digital signal only to the specific port where the destination MAC address is located.
When are SNMP traps sent? A. When the SNMP manager wants to perform remote configuration on a networking device B. When an SNMP agent wants to inform the SNMP manager about a change of state on the networking device C. When the SNMP manager wants to access large chunks of data D. When the NMS wants to share trap information
What is not a function of the distribution layer? A. Routing between VLANs B. Implement tools such as access lists, packet filtering, and queuing C. Implement security and network policies D. Provide workgroup/user access to the network
Which of the following three sets of IP addresses and subnet masks are private IP addresses? A. 10.0.0.0 255.0.0.0 B. 172.16.0.0 255.255.0.0 C. 172.16.0.0 255.240.0.0 D. 192.168.0.0 255.255.0.0
Match the following services with the correct descriptions: A. BRI 1. Provides two 64 Kbps B channels B. PRI 2. Provides 23 or 30 B channels 3. Provides one 16 Kbps D channel 4. Provides one 64 Kbps D channel 5. Provides a total bit rate of 2.048 Mbps in Europe and Australia 6. Provides a total bit rate of 144 Kbps 7. Provides a total bit rate of 1.544 Kbps in North America and Japan
Diagramming application information flow is important because: A. it helps identify heavy traffic paths B. it helps figure out why email gets from one place to another C. it can tell you when to purchase a new router D. it can tell you when to purchase a new switch
difference between layer 3 switch and router
0 Answers Aptron, Tech Mahindra,
What are the three commonly used methods of flow control used for handling network congestion? A. Buffering B. Source-quench messages C. Error checking D. Windowing
6. Which of these statements best describes VPLS ?
How can I release the restriction of CISCO2811C/K9? 10M optical fiber, Speed limit of 125kb / s, made by last network administrator, how can I release the restriction? Please tell me the detail, thanks! Cisco configuration： CISCO2811C/K9 ! ! ! ! ! ! ! interface FastEthernet0/0 description WANpork ip address x.x.x.x 255.255.255.248 ip access-group 110 in no ip proxy-arp ip verify unicast reverse-path ip nat outside ip virtual-reassembly duplex auto speed auto ! interface FastEthernet0/1 description LANpork ip address 192.168.x.x 255.255.255.0 ip access-group 101 in no ip proxy-arp ip verify unicast reverse-path ip nat inside ip virtual-reassembly rate-limit output 1000000 1000000 1000000 conform-action transmit exceed-action drop duplex auto speed auto !
CCNA 
