You have just issued the erase startup-config Command and reloaded your router.

You have just issued the erase startup-config Command and
reloaded your router. In which mode will your router be
when you react?

A. setup

B. startup

C. user EXEC

D. userd privileged

E. global configuration

Question Posted / guest

3 Answers
11659 Views
I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

You have just issued the erase startup-config Command and reloaded your router. In which mode will..

Answer / guest

Answer: A

Is This Answer Correct ?

20 Yes

6 No

You have just issued the erase startup-config Command and reloaded your router. In which mode will..

Answer / david michael franklin

Is This Answer Correct ?

9 Yes

4 No

You have just issued the erase startup-config Command and reloaded your router. In which mode will..

Answer / ranju

D. User Privileged

Is This Answer Correct ?

2 Yes

2 No

Post New Answer

More CCNA Interview Questions

what is the difference between a passive and active hub?? which is better ??

12 Answers

What is the maximum hop count for IP RIP? A.) Infinity B.) 16 C.) 15 D.) 1

2 Answers

What is the meaning of synchronization?

0 Answers

What are packets?

0 Answers

Which of the following is a connectionless protocol at the Transport layer? A.) UDP B.) ARP C.) ICMP D.) RARP E.) IP F.) FTP

4 Answers

Identify 2 transport layer protocols? A.) IP B.) TCP C.) CDP D.) ARP E.) UDP

1 Answers

What is default packet size of ipv6?

0 Answers

Hi Guys I am facing one problem while configuring PAP over Point to Point links. Configuration scenario is like this. ROUTER 1: (Hostname – R1) R1(config)#username R2 password CCNA2 R1(config)#interface serial 1/1 R1(config-if)ip address 10.0.0.1 255.0.0.0 R1(config-if)#lock rate 64000 R1(config-if)#encapsulation ppp R1(config-if)#ppp authentication pap R1(config-if)#ppp pap sent –username R1 password CCNA1 R1(config-if)#no shutdown ROUTER 2: (Hostname – R2) R2(config)#usename R1 password CCNA1 R2(config)#interface serial 1/1 R2(config-if)#ip address 10.0.0.2 255.0.0.0 R2(config-if)#encapsulation ppp R2(config-if)# ppp authentication pap R2(config-if)# ppp pap sent –username R2 password CCNA2 R2(config-if)#no shutdown Now problem is that, after configure the command “ppp authentication pap” the “Line protocol” status goes down on each router. But when I disable this command using “no ppp authentication pap”, the “Line Protocol” status goes up. What could be the problem, can anyone explain it plzzz….!!! Thanks in Advance…!! Shahin..

6 Answers

Which of the following will show an extended access list 150? A.) sh access-list B.) sh ip int C.) sh ip access-list 150 D.) sh access-list 150 extended

1 Answers

Which addresses are INCORRECTLY paired with their class? A. 128 to 191, Class B B. 192 to 223 Class B C. 128 to 191, Class C D. 192 to 223, Class C

3 Answers

Identify the command to run 'setup'? A.) Router(config)#setup B.) Router?setup C.) Router#setup D.) Router>setup

1 Answers Karrox,

Does a bridge divide a network into smaller sections?

0 Answers

For more CCNA Interview Questions Click Here