What is the attenuation?

0 Answers  

---

Which configuration task must you complete if a remote Frame Relay router does NOT support Inverse APP? A.configure static maps B.define an IP address locally C.disable DHCP on the Frame Relay router D.configure a static route to the remote network

1 Answers  

---

GUY i Have attended one interview for the data craft and they are offering me L1 postion and i am working at l2 in cisco so there is no way to get in the datacraft i am posting here the question he asked to and i have tested the interviewer and i come to know he was not having any knowledge. His questions are-: 1) what is Vlan 2) what is stp and what is difference between stp and RSTP 3) what is HSRP and Diffrence betwwen HSRP and GLBP 4) how to configure HSRP 5) Scenario Based question ( if we have two router and both are connected and there are having redundancy means two interface of the router r1 is connected to the two interface of Router R2 (R1)-------------(R2 (R1)-------------(R2 Now he want to configure the router in such a Manner that if one link down second link should come up.My answer was HSRP and his is "F looting static routing was i wrong "i know F looting Static routing is Theoretically possible but it is not fusible in the scenario where you have multiple router connected to the same router and if you have configured sub interface i challenged him and he lost The Battle and he get angary 5) what the eigrp and how it works 6) tables in eigrp 7) the information of feasible successor where it saved now after answering these all he was very angry ( i can fill the heat) 8) then he come to ospf Area type ( he was also not aware) 9) LSA type and its working ( he was also having confusion ) 10) then is asked routing by rummer( Theroy) 11) hello and dead intervel of EIGRp (theory) 12) Selection cretaria for Eigrp slecting best path ( here we have a long discussion on MTU and he lost the battle and agree That MTU never comes in the accounts in this process) 13) what is ACL type of acl ( here he was aware of TWO type Standard and extended i have told him 5 type( he again get Angry) We have 2hr of discussion and and he told me he will call me latter but i know he never call

1 Answers   IBM,

---

What is the purpose of a data link?

0 Answers  

---

Mention what is dhcp?

0 Answers  

---

Which three of the following are true statements about connection-oriented sessions? A.) The segments delivered are acknowledged back to the sender upon their reception B.) Any segments not acknowledged are retransmitted by the receiver C.) A manageable data flow is maintained in order to avoid congestion, overloading and loss of any data D.) Segments are sequenced back into their proper order upon arrival at their destination

3 Answers  

---

Identify 3 IP routing protocols? A.) RIP B.) AURP C.) OSPF D.) IGRP E.) ARP F.) ICMP

3 Answers  

---

'Show cdp neighbors detail' show the following 3 pieces of information? A.) Hardware platform B.) Software version C.) Same as 'show version' command D.) Up to 1 address for each protocol E.) Non-direct connected routers

2 Answers  

---

What is hsrp?

0 Answers  

---

hi friends i have some problem regarding technical round ahr round plz tell me what should the right answer technical questions 1 what is brouter 2 what is the menaing of 10 base2, 10 base 5 and 10baset 3 what is diffrence between bit rate and baud rate. and this question was tooooooooooo much difficult to me that hr said to me that rank me after the taking the all short of interview

5 Answers  

---

When discussing static routes, what is the gateway parameter used for? A.) Determining the dynamic route B.) Defining the subnet C.) Defining the Administrative Distance D.) Determining the next hop

1 Answers  

---

Identify 3 characteristics of a connection oriented protocol? A.) Path determination B.) Flow control C.) Acknowledgements D.) Uses hop count as metric E.) 3 way handshake

2 Answers  

---