Golgappa.net | Golgappa.org | BagIndia.net | BodyIndia.Com | CabIndia.net | CarsBikes.net | CarsBikes.org | CashIndia.net | ConsumerIndia.net | CookingIndia.net | DataIndia.net | DealIndia.net | EmailIndia.net | FirstTablet.com | FirstTourist.com | ForsaleIndia.net | IndiaBody.Com | IndiaCab.net | IndiaCash.net | IndiaModel.net | KidForum.net | OfficeIndia.net | PaysIndia.com | RestaurantIndia.net | RestaurantsIndia.net | SaleForum.net | SellForum.net | SoldIndia.com | StarIndia.net | TomatoCab.com | TomatoCabs.com | TownIndia.com
Interested to Buy Any Domain ? << Click Here >> for more details...


rate analysis for shuttering 1:6

Answers were Sorted based on User's Feedback



rate analysis for shuttering 1:6 ..

Answer / sjtbehera

what is mean by shuttering 1:6

shuttering are measure by sqm or sqft.

anyalisis can be done by taking plywood, support ( Bolly)
and batten

Is This Answer Correct ?    10 Yes 0 No

rate analysis for shuttering 1:6 ..

Answer / kumars

1:6 Ratio Should Not Applicable for Shuttering, please Give Clear Idea About Your Quotation.

it can be done in Sqm or Sft, Go For Refernce IS Code For Better Understanding. IS 1200

Is This Answer Correct ?    0 Yes 0 No

Post New Answer

More Civil Engineering Interview Questions

Define What are the reasons for geotechnical site investigations in Uganda?

0 Answers  


What is the diameter of the 3"inch nails?

0 Answers   Rohan Builders,


wat is six sigma course ? is it good for civil engineers . wat is pmp certification ? is it good for civil engineers .

1 Answers   CCCL,


I am called for interview from north east power plant .so, I need some interview question which may help me.

0 Answers   Power Plant,


How to design a beam without any typical(tuff) calculation. Answer Only by using site practical knowledge?

1 Answers  


What is the maximum cement content allowed in RCC?

11 Answers   L&T,


Pl answer. when we deduct 2d for cutting length of 90deg bend, whats the method of booking measurements as per IS code? whether cutting Length to be booked or something else?

2 Answers   Chettinad,


suppose we have a tendency to make a hole on the surface of the simple supported beam, than where we goes to make it?

0 Answers  


how much CM required for Random Rubble masonry in CM 1:6

1 Answers  


What is proportion of M25,M30,M35,M40 IN TH FORM 1,2,3,4?

12 Answers   L&T,


what motivates you to do a good job

1 Answers   Flextronics, HPCL, ISRO,


Can a 24" RCC beam can rest on 18" RCC beam.

2 Answers  


Categories
  • Civil Engineering Interview Questions Civil Engineering (5086)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4453)
  • Electrical Engineering Interview Questions Electrical Engineering (16638)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1095)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)