Which OSI Reference Layer controls application to application communication?

Which OSI Reference Layer controls application to application

communication?

A.) Datalink

B.) Network

C.) Transport

D.) Session

E.) Physical

Question Posted / guest

3 Answers
6900 Views
I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

Which OSI Reference Layer controls application to application communication? A.) Datalink B..

Answer / guest

Answer: D

Is This Answer Correct ?

7 Yes

0 No

Which OSI Reference Layer controls application to application communication? A.) Datalink B..

Answer / prashant shinde

session

Is This Answer Correct ?

3 Yes

0 No

Which OSI Reference Layer controls application to application communication? A.) Datalink B..

Answer / rahul tiwari

presentation layer

Is This Answer Correct ?

1 Yes

1 No

Post New Answer

More CCNA Interview Questions

I am facing one problem in my layer 2 switch I don’t know the problem is on switch side or client side. The problem is some PC (not all) are stop participate in LAN they don’t send or recd. Packet from switch and if I check RJ45 (with LAN tester)from PC side the packet and 8 pin wire is working fine and after that process of LAN tester I plug RJ 45 in PC now PC start recd/ send packets what is the problem I don’t understand even client side no virus found RJ45 is ok and switch has no problem bcoz other PC is working fine Cable (cat 5 ) is also fine bcoz I didn’t crimp again just check in LAN tester and start working fine. Plz any one solve this matter. And after lan tester process pc is working fine and after 2 or 3 hour it again start same problem and again same process lan tester I have used

5 Answers

What is Transport and Tunnel mode?

0 Answers CCIE,

How can you add the 192.168.100.0/30 network to EIGRP without involving the 192.168.100.4/30 network as well?

6 Answers

The Datalink Layer is broken down into 2 layers, LLC and MAC. The LLC establishes media independence and what else? A.) Provides Windowing. B.) Provides flow control. C.) Provides SAP's (Service Access Points). D.) The Datalink layer does not have sublayers. E.) Provides SAP's (Service Advertising Protocol). F.) RIP Updates.

2 Answers

Identify the command to display the Frame Relay map table? A.) Router# display frame-relay map B.) Router# show frame-relay map C.) Router(setup)# show frame-relay map D.) Router# show map frame-relay

1 Answers

Which layer defines bit synchronization? A.) Application B.) Network C.) Transport D.) Physical E.) Session F.) Session

2 Answers

As a system administrator, you need to provide your routers with a Domain Name System (DNS) server. How many DNS servers can you specify with one command? A. 6 B. 1 C. 2 D. 4

1 Answers

Which of the following provide correct information about a protocol at the transport layer of the OSI model? A.) UDP - Provides Connectionless datagrams service B.) TCP - Provides Connection Oriented Services C.) SMTP - Provides Mail Exchange D.) IP - Route determination E.) TCP - Provides Flow Control and Error Checking F.) FTP - Transfers of Files

2 Answers

What is poe (power over ethernet)?

0 Answers

What does -1 signify in an extended IPX access list? A. permit this host B. deny this host C. permit only this subnet D. any host or any network

2 Answers

Why would you use static routing instead of dynamic routing? A.) When you want automatic updates of the routing tables B.) All the time C.) When you have very few routes and want to conserve bandwidth D.) When you have a gateway of last resort

1 Answers

If configuring a Cisco router to connect to a non-Cisco router across a Frame Relay network, which encapsulation type would you select? A.) Q933a B.) ISDN C.) IETF D.) CISCO E.) ANSI

1 Answers

For more CCNA Interview Questions Click Here