Interested to Buy Any Domain ? << Click Here >> for more details...
When would you use ISDN?
A.) To connect LANs using POTS
B.) To support applications requiring voice, data, and video
C.) When you need a consistent and very high rate of data speed
D.) To connect to IBM mainframes
- 2 Answers
- 5317 Views
- I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
(1)what is "rtp" and how it work, (2)what is diffrence between igrp and eigrp (3)the slection prcedure of dr and bdr is depend open (4)why frame really is called nbma (5)what is ppp (6) what is diffrence b/w tcp and udp (7) how can we implement ospf protocall on any router (8)whta is as nomber (9)what is AD value (10)what is the broadcast id,n/w id and number of vallid host of the 255.255.255.128/25 195.168.10.10/25 (11) what is stub network (12) what is contigues n/w (13)on which type of router we can implement default routing (14)what is diffrence b/w hub switch;switch router, (15)what is v lan (16)what is the diffrence b/w link sate protocal and distance vector protocall (17)what is synchoransh mode of data transfer and asynchronash mode of data transfer (18) question on lab, belive me frnds there are 20 questions and 5 questions on lab implimentaion.around 1.1/2 hour i was in interview room and after givieng 17 right answera and 4 in lab i got slected try to give answer if any difficulty or any prob plz email me on jitenderasinha.it@gmail.com if any one of you havae boson netsim plz also intimate me
Which two types of route table entries are used by a Layer 3 router to determine the appropriate path to destination? (Choose two) A. static route entry B. default route entry C. Dynamic route entry D. temporary route entry E. permanent route entry
what is eigrp and what is the benfit of eigrp over igrp what is route summryization if one the router route is not showing the what should be problem how to resolve these problem what is fessible suceer. is the load balncing is one of the property of eigrp what is the metihod of authantication what is the diffrnec betwee pap and chap what is stp command for enabling stp and rstp why switching loop occur what is the main factor of ocuring switch loop what is the mechnaism for stoping the roting loop what is best diffrence betwwen ospf v1 nad ospf v2 what is vtp what is the diffrence between vtp version 1 and veron 2 what is the ip address what is the diffrence betwwen ip address mac address what is dhcp and how it work what is 3 way hand shake what is the difrence betwwen network id and brodcast id what is the network id for 111.111.111.10/29 what is the command for enabling vlan on 3650 csco switch
Which of the following are logged when IP access list logging is enabled? A.) source address B.) protocol C.) source port D.) destination address E.) access list number F.) destination port
can we measure how much a host exact bandwidth using by a network cable which is communicating over the network? options: 1- via Router 2- Switch, 3- other device... if yes.. then how ( with every option)
Hi Guys I am facing one problem while configuring PAP over Point to Point links. Configuration scenario is like this. ROUTER 1: (Hostname – R1) R1(config)#username R2 password CCNA2 R1(config)#interface serial 1/1 R1(config-if)ip address 10.0.0.1 255.0.0.0 R1(config-if)#lock rate 64000 R1(config-if)#encapsulation ppp R1(config-if)#ppp authentication pap R1(config-if)#ppp pap sent –username R1 password CCNA1 R1(config-if)#no shutdown ROUTER 2: (Hostname – R2) R2(config)#usename R1 password CCNA1 R2(config)#interface serial 1/1 R2(config-if)#ip address 10.0.0.2 255.0.0.0 R2(config-if)#encapsulation ppp R2(config-if)# ppp authentication pap R2(config-if)# ppp pap sent –username R2 password CCNA2 R2(config-if)#no shutdown Now problem is that, after configure the command “ppp authentication pap” the “Line protocol” status goes down on each router. But when I disable this command using “no ppp authentication pap”, the “Line Protocol” status goes up. What could be the problem, can anyone explain it plzzz….!!! Thanks in Advance…!! Shahin..
Which three statements about Frame Relay configurations using subinterfaces is true? (Choose three) A. Each subinterface is conferred either multipoint or point to point B. Any network address must be removed from the physical interface C. The configuration of subinterfaces is done in router (config-if)# mode D. Frame Relay encapsulation must be conferred on each subinterface
Hi all of you, Actually this is interview qe? but i did,t do explain it completely so please give reply recently and completly Ans, what is sub-interface and inter-vlan ? And How to implement it on cisco router & switches and also which series router switches supported please write..........
In stead of 0.0.0.0 wild card mask what you can write after ip?
Which protocols do periodically updates?
Name the vtp modes?
What is the default encapsulation of Netware 3.12? A.) Ethernet_II B.) 802.5 C.) 802.2 D.) 802.3
CCNA 
