Answer / bharat_n86n

the speed of signal is as similar as light , mean the data
sending speed is 3*100000000m/s
or
3*10(8) m/s

Answer / rajat

the speed of signal is 1200 kbps

Answer / sagar

The optical refractive index of fused silica (SiO2) glass is
modified with dopants to
produce a core light guiding region with an optical
refractive index that is 1.0 to 1.5
percent greater than the cladding glass. For multimode and
single mode step index fibers
operating at wavelengths near 850 nm a typical cladding
would have a refractive index of
1.518 and the core would have a refractive index of 1.538
which is 1.3% greater. The
velocity of propagation in the multimode step index fiber
would be near the speed of light
(c) divided by 1.538. Single mode step index fibers would
have a slightly lower velocity of
propagation because a good portion of the optical mode
travels in the cladding layer. To
confine the single mode more tightly to the core fibers with
a W refractive index profile
have been developed; however, the major reason that the W
profile was develops was to
reduce wavelength dispersion (velocity differences) in the
system which limits the product
of the fiber length and operating bandwidth.

Graded index fibers have a complex refractive index profile
with an index well and a
parabolic index core. An index profile for a graded index
fiber taken
from Midwinter’s book is shown below.
____
____
_
__
_____
__________
___________
__________
_____
__
_
___
___

The diameter of the parabolic core is 40 micrometers with a
change of index at the center
of the core (relative to the cladding) of +0.01.
The depressed well has a diameter between 40 and 60
micrometers with a change of index
(relative to the cladding) of -0.003 at the minimum. It is
very difficult to calculate the
composite velocity of propagation in graded index fibers
because of the complex path
through which each ray travels.

In my radar related work we have constructed precision
programmable fiber optic delay
lines with one picosecond steps in delay over 100 km (60
mile) lengths. In all cases we
could not rely on calculating the velocity within the fibers
and we had to make precise
time delay measurements while trimming the length of the
fibers. At this point thermal
changes in the length of the fibers also becomes an
important factor and the temperature
of the long of the fibers must be also be stabilized.

The Jet Propulsion Laboratory's Deep Space Network antennas
at Goldstone, CA use
optical fiber links to transmit atomic clock signals between
antennas to phase them for
microwave frequency inteferometric measurements. They also
have to stabilize the
temperature of their several kilometer long distribution links.

areas for improvement

0 Answers  

---

Which series of ICs are used for military applications?

2 Answers   BEL, NTPC,

---

plz send me previous question paper of RRB section Engineer- Electronics ,erpdayal@gmail.com

0 Answers  

---

The ratio of Emissive to absorption power of heat by a body is equal to heat emitted by a perfect black body. Who said the statement

0 Answers   HAL,

---

What is potential transformers?

0 Answers  

---

What are the control strategies of chopper?

0 Answers  

---

Explain the different steps of Commissioning.

0 Answers   NSN,

---

hi friends, i have applied for oces 2010. can u give me a brief idea about the entrance exam which is gng to be held on may30th.Is the exam of technical or it includes aptitude? i am from ece stream.pls mail me at navinmsl@gmail.com

1 Answers  

---

why we used -48 dc volt for telecom equipments ?

2 Answers  

---

what is GPS & GPRS?What is diff. among them?

3 Answers  

---

Define positive logic

0 Answers  

---

How many maximum slots we can use in ESMA card?

0 Answers   NSN,

---