Which OSI layer incorporates the MAC address and the LLC? A.) Data link B.

Which OSI layer incorporates the MAC address and the LLC?

A.) Data link

B.) Network

C.) Physcial

D.) Transport

Question Posted / guest

4 Answers
11037 Views
I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

Which OSI layer incorporates the MAC address and the LLC? A.) Data link B.) Network C.) Phy..

Answer / m haja bahurudeen

A.) Data link

Is This Answer Correct ?

11 Yes

2 No

Which OSI layer incorporates the MAC address and the LLC? A.) Data link B.) Network C.) Phy..

Answer / guest

Answer: A

Is This Answer Correct ?

8 Yes

2 No

Which OSI layer incorporates the MAC address and the LLC? A.) Data link B.) Network C.) Phy..

Answer / phan binh

Where do the MAC sublayers fit into the OSI model?
Đáp án :
a. Transport
b. Network
c. Data Link
d. Presentation
e. Physical

Is This Answer Correct ?

2 Yes

0 No

Which OSI layer incorporates the MAC address and the LLC? A.) Data link B.) Network C.) Phy..

Answer / raghu

B.) network

Is This Answer Correct ?

3 Yes

3 No

Post New Answer

More CCNA Interview Questions

Hello Mr.Jitendera Kuamr Sinha, how is every thing going on? Thanks for your reply. Dear Friend if you can Explain it little bit deeper i will be realy thanks full. Wish you all the Best.

1 Answers

When you enter router passwords during the setup dialog what is the difference between enable and the enable secret passwords? A. The enable password is encrypted B. The enable secret password uses IPSec password authentication C. The enable secret password cannot be seen as clear text when viewing the configuration D. The enable secret password acts as a backup in case the enable password is compromised

8 Answers Wipro,

Which of the following are valid WAN terms? A.) DTE B.) DCE C.) Demarc D.) CPE

3 Answers IBM,

Which IP address and wildcard mask would you use in your ACL to block all the hosts in the subnet 192.168.16.43/28?

2 Answers Siemens,

Hi Guys i hv one confusion. Need u peoples help. In EIGRP, maximum hop count is up to 255. By default only 100. Now question is - a) Suppose i hv a network consist of 115 routers & EIGRP routing protocol is configured. By default hop count is 100, so is there any manual configuration necessary for hop count ya router will automatically detect the hop count & will update the hop count accordingly..????? b) In EIGRP, Bandwidth & Delay is used to calculate metric. For this Metric weight is set to K1(Bandwidth)=1, K2(Delay)=0, K3(Reliability)=1, K4(Load)=0, K5(MTU)=0 Now i want, Bandwidth & Load is used to calculate metric. For that wat i hv to configure & wat wub the metric weights. Cud anyone explain it plzzzz..!!!!

5 Answers

What are the things that can be accessed in a CISCO router’s identifying information?

0 Answers

As system administrator, you type "debug ipx sap" and receive the following lines as part of the IOS response: type 0x4, "HELLO2", 199.0002.0003.0006 (451), 2 hops type 0x4, "HELLO1", 199.0002.0003.0008 (451), 2 hops What does "0x4" signify? A. That is a Get Nearest Server response. B. That it is a General query. C. That it is a General response. D. That it is a Get Nearest Server request.

2 Answers Microsoft,

When we do default route?

0 Answers

The Datalink layer works with which of the following: A.) Packets B.) Bits C.) Globules D.) Frames E.) Segments

1 Answers

What are the types of resource sharing?

0 Answers

What is the routing metric used by RIP? A.) Route poisoning B.) Split horizon C.) Hop Count D.) TTL

4 Answers jetking, Tata Motors,

What is the difference between csma/cd?

0 Answers

For more CCNA Interview Questions Click Here