Identify the command to run 'setup'?
A.) Router(config)#setup
B.) Router?setup
C.) Router#setup
D.) Router>setup
- 1 Answers
- 3196 Views
- I also Faced
- E-Mail Answers
WHY DO WE USE the command interface Vlan 1 ip adress x.x.x.x sub mask what does it do .. what does it create.. i know when we create it we can remotely telnet inti a router=switch. but what is the diff bwt vlan and intface vlan. ... vlan 1 bieng a native vlan remains there eve if i dont gv switch an ip address .. lease suggest.
Identify the hardware component that stores the backup configuration? A.) RAM B.) NVRAM C.) Flash D.) ROM
What is an advantage of LAN segmentation? A.) Increases broadcasts. B.) Increases collisions. C.) Provides more protocol support. D.) Decreases broadcasts. E.) Routing protocol support.
Which command will display adjacent routers found by the Cisco Discovery Protocol? A.) show all B.) show cdp entry C.) show ip neighbors D.) show cdp neighbor detail E.) show cdp neighbor F.) show neighbor
Which two physical interfaces support PPP? (Choose two) A. Ethernet B. Token Ring C. Synchronous serial D. Asynchronous serial
Explain the types of ospf configuration?
Which layer is responsible for flow control, acknowledgement, and windowing? A.) Transport B.) Network C.) Application D.) Session E.) Physical F.) Data Link
Which of the following is not a characteristic of link-state routing protocols? ❍ A. VLSM support ❍ B. Route summarization at any bit level ❍ C. Full routing updates at regular intervals ❍ D. Discontiguous network support
The CSMA/CD Ethernet IEEE committee is defines as which of the following? A.) 802.2 B.) 802.3 C.) 802.4 D.) 802.5
GUY i Have attended one interview for the data craft and they are offering me L1 postion and i am working at l2 in cisco so there is no way to get in the datacraft i am posting here the question he asked to and i have tested the interviewer and i come to know he was not having any knowledge. His questions are-: 1) what is Vlan 2) what is stp and what is difference between stp and RSTP 3) what is HSRP and Diffrence betwwen HSRP and GLBP 4) how to configure HSRP 5) Scenario Based question ( if we have two router and both are connected and there are having redundancy means two interface of the router r1 is connected to the two interface of Router R2 (R1)-------------(R2 (R1)-------------(R2 Now he want to configure the router in such a Manner that if one link down second link should come up.My answer was HSRP and his is "F looting static routing was i wrong "i know F looting Static routing is Theoretically possible but it is not fusible in the scenario where you have multiple router connected to the same router and if you have configured sub interface i challenged him and he lost The Battle and he get angary 5) what the eigrp and how it works 6) tables in eigrp 7) the information of feasible successor where it saved now after answering these all he was very angry ( i can fill the heat) 8) then he come to ospf Area type ( he was also not aware) 9) LSA type and its working ( he was also having confusion ) 10) then is asked routing by rummer( Theroy) 11) hello and dead intervel of EIGRp (theory) 12) Selection cretaria for Eigrp slecting best path ( here we have a long discussion on MTU and he lost the battle and agree That MTU never comes in the accounts in this process) 13) what is ACL type of acl ( here he was aware of TWO type Standard and extended i have told him 5 type( he again get Angry) We have 2hr of discussion and and he told me he will call me latter but i know he never call
How many Frame-relay encapsulation types are available with Cisco routers? A.) Four B.) Two C.) Five D.) Three
What are 3 ways to provide login access to router? A.) Console B.) TFTP C.) Rlogin D.) Auxiliary Port E.) X Windows F.) Telnet
CCNA 
