The Datalink layer works with which of the following:
A.) Packets
B.) Bits
C.) Globules
D.) Frames
E.) Segments
- 1 Answers
- 4730 Views
- I also Faced
- E-Mail Answers
Answer / guest
Answer: D
Physical - bits
Datalink - frames
Network - packets
| Is This Answer Correct ? | 3 Yes | 0 No |
What does aaa stands for?
What is de-encapsulation?
Which statement is true? A. While bridges are used to segment networks, they will not isolate broadcast or multicast packets. B. A bridge looks at every packet within its network segment and works like a hub re-broadcasting the packet if the destination is within its network segment. C. A bridge maintains a table of the IP addresses of the hosts within its network segment and forwards the packet directly to the destination based upon the IP address. D. A bridge resets the hop count by keeping all packets within the network segment. Only packets addressed to a specific destination host outside the network segment are allowed to pass through the bridge.
Which command will display the encapsulation type on interface serial 0? A.) show interface s0 B.) show all C.) show int s0 encap D.) show encap s0 E.) show encap
What is the Broadcast MAC Address?
The following selections show the command prompt and the configuration of the IP network mask. Which two are correct? A. Router#term IP netmask-format { bitcount | decimal | hexadecimal } B. Router(config-if)#IP netmask-format { bitcount | decimal | hexadecimal } C. Router(config-if)#netmask-format { bitcount | decimal | hexadecimal } D. Router#ip netmask-format { bitcount | decimal | hexadecimal }
How many types of nat?
How can you add the 192.168.100.0/30 network to EIGRP without involving the 192.168.100.4/30 network as well?
1350 Value in which type of access-list?
IPX routing updates occur how often? A.) Every 30 seconds B.) Every 60 seconds C.) Only as needed D.) When the remote router asks for an update
Which commands will restart the router? A.) router#system exit B.) router >reload C.) router#shutdown D.) router#reload E.) router#(config)reload F.) router#system restart
GUY i Have attended one interview for the data craft and they are offering me L1 postion and i am working at l2 in cisco so there is no way to get in the datacraft i am posting here the question he asked to and i have tested the interviewer and i come to know he was not having any knowledge. His questions are-: 1) what is Vlan 2) what is stp and what is difference between stp and RSTP 3) what is HSRP and Diffrence betwwen HSRP and GLBP 4) how to configure HSRP 5) Scenario Based question ( if we have two router and both are connected and there are having redundancy means two interface of the router r1 is connected to the two interface of Router R2 (R1)-------------(R2 (R1)-------------(R2 Now he want to configure the router in such a Manner that if one link down second link should come up.My answer was HSRP and his is "F looting static routing was i wrong "i know F looting Static routing is Theoretically possible but it is not fusible in the scenario where you have multiple router connected to the same router and if you have configured sub interface i challenged him and he lost The Battle and he get angary 5) what the eigrp and how it works 6) tables in eigrp 7) the information of feasible successor where it saved now after answering these all he was very angry ( i can fill the heat) 8) then he come to ospf Area type ( he was also not aware) 9) LSA type and its working ( he was also having confusion ) 10) then is asked routing by rummer( Theroy) 11) hello and dead intervel of EIGRp (theory) 12) Selection cretaria for Eigrp slecting best path ( here we have a long discussion on MTU and he lost the battle and agree That MTU never comes in the accounts in this process) 13) what is ACL type of acl ( here he was aware of TWO type Standard and extended i have told him 5 type( he again get Angry) We have 2hr of discussion and and he told me he will call me latter but i know he never call
CCNA 
