CSMA/CD stand for which of the following?
A.) Carrier Sense, Multiple Access with Collision Detection
B.) Collision Sense, Multiple Access with Collision Detection
C.) Collision Sense, Multiple Access with Carrier Detection
D.) Carrier Sense, MAC address with Collision Detection
- 1 Answers
- 4674 Views
- I also Faced
- E-Mail Answers
Answer / guest
Answer: A
The IEEE standard for Carrier Sense Multiple Access / Collision
Detection is 802.3. Also know as Ethernet.
| Is This Answer Correct ? | 3 Yes | 0 No |
what is the difference between a passive and active hub?? which is better ??
What is the mau?
hi i am facing one problem.ptoblem is like that i am getting output error on mine router ethernet interfae here is the cisco#show interface e0 Ethernet0 is up, line protocol is up Hardware is QUICC Ethernet, address is 0030.802d.2a17 (bia 0030.802d.2a17) Internet address is 202.122.20.225/28 MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec) ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:00, output 00:00:00, output hang never Last clearing of "show interface" counters 05:55:07 Queueing strategy: fifo Output queue 0/40, 0 drops; input queue 0/75, 0 drops 5 minute input rate 10000 bits/sec, 11 packets/sec 5 minute output rate 29000 bits/sec, 11 packets/sec 1515202 packets input, 359100396 bytes, 1 no buffer Received 6 broadcasts, 0 runts, 0 giants, 1 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 0 input packets with dribble condition detected 1584394 packets output, 1623395338 bytes, 0 underruns 1820 output errors, 26732 collisions, 0 interface resets 0 babbles, 0 late collision, 9698 deferred 18 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out output cisco# what is the reason how to solve this please tell me i am using cisco asa 5520 behid mine internet router and no error on the asa inside interface
"sap" is used by the Cisco IOS for which encapsulation types? A. Ethernet_802.2 B. Token-Ring C. FDDI_SNAP D. Ethernet_802.3 E. FDDI_802.2
What will be the prefix length of 224 in vlsm?
Explain the difference between switch & hub?
Can you explain L2TP?
What is VLSM ?
What is the administrative distance for RIP? A.) 100 B.) 90 C.) 120 D.) 110
'Show cdp neighbors detail' show the following 3 pieces of information? A.) Hardware platform B.) Software version C.) Same as 'show version' command D.) Up to 1 address for each protocol E.) Non-direct connected routers
Tell me how many fillers we can put in one ip of ipv6?
please point out the wrong steps in that l3 switch conf Building configuration…… Current configuration : 1802 byte ! Version 12.2 no service pad Service timestamps debug uptime no service-password encryptions ! hostname xxxx ! enble secret XXXXXXXXXXX(omitted) enable password jitendera kumar sinha ! No aaa new-model System mtu routing 1500 bytes ip subnet-zero ip routing ip name-server 202.x.x.x. ip name –server 203.x.x.x ip name-server 192.168.x.x ip dhcp excluded-address 172.x.x.x 172.x.x.x ! ip dhcp pool ss network 172..x.x.x 255.255.255.0 domain-name xxx.com default-router 172.x.x.x dns-server 192.x.x.x 203..x.x.x 202.x.x.x lease10 ! ! ! ! ! no file verify auto spanning-tree maode pvst spanning-tree extended system-id ! vlan internel allocation policy ascending ! interface fastethernet 0/1 no switch port ip address 172.x.x.x 255.255.255.0 ! interface fastethernet 0/2 no switch port ip address 192.x.x.x ! interface fastethernet 0/3 switcport access vlan 5 switchport mode access ! interface fastethernet 0/4 Switcport access vlan 5 Switchport mode access ! interface fastethernet 0/5 Switcport access vlan 5 Switchport mode access ! interface fastethernet 0/6 Switcport access vlan 5 Switchport mode access ! interface fastethernet 0/7 Switcport access vlan 5 Switchport mode access ! interface fastethernet 0/8 Switcport access vlan 5 Switchport mode access ! interface fastethernet 0/9 Switcport access vlan 5 Switchport mode access ! interface fastethernet 0/10 Switcport access vlan 5 Switchport mode access ! interface fastethernet 0/11 Switcport access vlan 5 Switchport mode access ! interface fastethernet 0/12 Switcport access vlan 5 Switchport mode access ! Interface fastethernet 0/13 Switcport access vlan 5 Switchport mode access ! Interface fastethernet 0/14 Switcport access vlan 5 Switchport mode access ! Interface fastethernet 0/15 Switcport access vlan 5 Switchport mode access ! Interface fastethernet 0/16 Switcport access vlan 5 Switchport mode access ! Interface fastethernet 0/17 Switcport access vlan 5 Switchport mode access ! Interface fastethernet 0/18 Switcport access vlan 5 Switchport mode access ! Interface fastethernet 0/19 Switcport access vlan 5 Switchport mode access ! Interface fastethernet 0/20 Switcport access vlan 5 Switchport mode access ! Interface fastethernet 0/21 Switcport access vlan 5 Switchport mode access ! Interface fastethernet 0/22 Switcport access vlan 5 Switchport mode access ! Interface fastethernet 0/23 Switcport access vlan 5 Switchport mode access ! Interface fastethernet 0/24 Switcport access vlan 5 Switchport mode access ! Interface vlan 1 No ip address Shutdown ! Interface vlan 5 Ip address 172.16.x.x 255.255.255.0 ! Ip default-gateway 172.16.32.1 ! Ip classless Ip route 0.0.0.0 0.0.0.0 fastethernet 0/1 172.x.x.x Ip route 0.0.0.0 0.0.0.0 fasrethernet 0/2 192.168.x.x 254 Ip http-server ! ! Control-plane ! ! Line console 0 Line vty 0 4 Password password Login Line vty 5 15 Password password Login ! end chek out the wrong steps and post it. i ma not able to ping firewall
CCNA 
