Sir Power transformer :- (in generating station) Alternator terminals side

Sir
Power transformer :- (in generating station)
Alternator terminals side - Delta
HT transmission line side - Star
Why?

Question Posted / guest

4 Answers
7942 Views
Kirloskar, I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

Sir Power transformer :- (in generating station) Alternator terminals side - Delta HT transmissio..

Answer / anup mohan

I could not understand the question clearly... but.. in generating n transmitting the terminals are in delta... as we need only 3 phases..... but at the other end.. i.e on the distribution end.. the connections are in star/wye... thtas ca.. in addition to the 3 phases we need a neutral... we ve neutral conection only in star and not in delta

Is This Answer Correct ?

3 Yes

3 No

Sir Power transformer :- (in generating station) Alternator terminals side - Delta HT transmissio..

Answer / nagarajan

Example 15mva,220/132kv
Star 220kv here phase voltage =line volatge/1.732=127kv
delta 11kv here phase voltage =line volatge.
Because star side we have neutral ,a.insulation cost less and 127kv insulation is sufficient but in this delta we require 132kv insulation.

Is This Answer Correct ?

0 Yes

0 No

Sir Power transformer :- (in generating station) Alternator terminals side - Delta HT transmissio..

Answer / kc

To reduce the fault level

The fault on primary side ie Y (LLG)
Will reflect as a LL Fault

So fault current level will b less
No zero sequence current ll b appar on d secondary side

Is This Answer Correct ?

0 Yes

0 No

Sir Power transformer :- (in generating station) Alternator terminals side - Delta HT transmissio..

Answer / bhim kumar yadav(l&t)

bcz in delta side voltage is more compare to star side. so
insulation cost is very-very high in delta side compared to
star side.therefor, we keep always star connection in HT
side

Is This Answer Correct ?

2 Yes

3 No

Post New Answer

More Electrical Engineering Interview Questions

tell me any book for current n potential trasformer with full knowledge ?

1 Answers

Why in 6 KV XLPE cable termination kit used and why not in 380 V xlpe cable same is not used

0 Answers

is that any software calculator to calculate the size of cable

0 Answers JSW,

my 10 hp submersible pump is tripping when connected through ELCB.I have checked the megger value of the coil's with body.It was found to be 0.2mega ohm.that is leakage is there.But when connected to mccb it is not tripping.no leakage current in the motor.Is it safe to connect to mccb? what are the problem's will arise if future?also tell me in ELCB no neutral is connected to motor.than how ELCB was working?

1 Answers

if we install two earth pits with a clear space of 5m without any interconnection,by checking the digital multimeter will it show continuity between earth pits? If so what would be the approx. value

0 Answers

WHEN THESE TRANSFORMERS WINDINS CONFIGURATION ARE USED? SPECIALLY EXPLAIN REGARDING STEP UP AND STEP DOWN KEEPING IN MIND.AND REGARDING LOAD ALSO. a.star to delta b.delta to star c.delta to delta d.star to star ALSO EXPLAIN WHY V USE 415/415 TRANSFORMERS IN TUBEWELLS?

1 Answers ABB,

what is the difference between delta delta and star delta connection transformer? why we use delta delta transformer since it need earthing transformer for grounding?

0 Answers

what is main parts of alternator.

3 Answers HP,

Why the moulded plug comes with domestic appliances instead of assembled plug like anchor, Vinay 5/15 A.

0 Answers

What is the basic principle of welding process?

0 Answers

Hi Recently I got one formula that is Impedence of Xformer = Rated KVA/Root 3 * secondry voltage OF Xformer. Is it Right??????

2 Answers

What will happen if i connect the delta winding motor to star input.

1 Answers

For more Electrical Engineering Interview Questions Click Here