how we can check the CT & VT?

Answers were Sorted based on User's Feedback



how we can check the CT & VT?..

Answer / sri krishna

the question was incoorect or inkomplete.
ok
if wanna know vch is ct nvch is vt..
bye obserrving the windings of the t/f s we can conclude
vch is ct and vch is vt.

ct has only 1 turn in the priamry side, (vch was thik and
generally flat) and the secondary has number of turns..

where as vt has many number of tunrs on the primary side and
secindary has comparatuvely less numbr of turns.

note: like the general t/f s the cts and vts shud not b used
in any manner.i.e the primary and secondary shud not be the
any 1 winding of the tf. but striktly, primary shud priamary
alwwaayss..

Is This Answer Correct ?    1 Yes 1 No

how we can check the CT & VT?..

Answer / master ramunniraja

CT Primary turn wire thickness is very thick compared to
secondary wire. Primary having only one turn.

PT Primary and secondary wires are thin depend upon the
rating of the transformer.

Is This Answer Correct ?    0 Yes 0 No

Post New Answer

More Electrical Engineering Interview Questions

i am an maintenance engineer. one distribution board have 5 feeder. recently its ELR trips frequently, but it take some times after trip( 10min,20min..)but 3 feeder no load. two feeder only loaded. i checked one feeder IR value all values are above 50Mohm.but B phase to Earth is only 9Mohm.any problem about low value

0 Answers  


how to calculate cable size by amp

19 Answers   CDS,


why transformer measures in kva

4 Answers  


What is the standard height of installation of Socket & switch from Finish Floor Level as per the IEC/IS Rules?

1 Answers  


How can we increase the capacity of exixting capacitor bank??????????????? PLS. Help

1 Answers  






what is the difference between the electrical and electronic choke?

1 Answers  


what is a diffrence between MCCB, RCCB, MCB, & ELCB ? what is rated current e.g. on motor name plate indicated that is rated curent? what is full load current? If we run D.C. motor with mechanical coupling and we measure voltage on terminal it shows voltage or not ? same in AC also possible ?

5 Answers   Reliance,


Why the frequency of ac in india is 50 hz but in some other countries it is 60 hz.

0 Answers   BARC, Fedco, Qasco,


If we increase frequency in transmission line in lieu of voltage what will happen?

1 Answers  


what is droop?

13 Answers   Alstom, Bhel,


what is the principle of generator , induction motor,d.c motor

1 Answers  


why high speed tripping relay will be used in tripping circuit why not normal relay

0 Answers  


Categories
  • Civil Engineering Interview Questions Civil Engineering (5085)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4451)
  • Electrical Engineering Interview Questions Electrical Engineering (16632)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1095)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)