Answer / engineer muhammad amin baloch

Negative air pressure generated by buoyancy of hot gasses
inside furnace is called draft

What is the method of determining maximum differential pressure during hydro testing of shell and tube heat exchangers?

0 Answers  

---

what is R1,R2,R3, R4........?

0 Answers   Okaya,

---

How to caliculate the boil up rate, dia and height in both packed and tray distillation columns and any referance books for the design.

0 Answers  

---

What is a good source of equations for calculating discharge flowrates from accidental releases?

0 Answers  

---

What is a good method of steam tracing large vessels?

0 Answers  

---

Chemical Engineering Energy Balance - Please match the term A - E as follow with the stated definition : A. Yield. B. Selectivity. C. Relative saturation. D. Molal saturation. E. Absolute saturation. i. Answer : ? (moles of desired product formed) / (moles that would have been formed if there were no side reactions and the limiting reactant has reacted completely). ii. Answer : ? (moles of desired product formed) / (moles of undesired product formed). iii. Answer : ? (relative humidity 40 % means partial pressure of water vapour equals 4 / 10 of the vapour pressure of water at the system temperature). iv. Answer : ? (moles of vapour) / (moles of vapour dry gas). v. Answer : ? (mass of vapour) / (mass of dry gas).

1 Answers  

---

Question 70 - According to Adolf Eugen Fick (1829 - 1901) : rate of diffusion v increases with less wall thickness t, increased area A and decreased molecular weight of a fluid M. The diffusion constant D decreased with increasing M. (a) By assuming v, t, dP, A, M and D changes proportionally of each other, find the equation of v as a function of t, dP, A and D. (b) The ratio of self diffusion constant D, at T = 273 K and P = 0.1 MPa, for gases B and C are 1.604 : 0.155. If only 2 gases exist in such a system : hydrogen and nitrogen, find the type of gas for B and C with reference to their molecular weights M. (c) By using the equation of kinetic energy 0.5 MV = constant where V = square of v, find the ratio of V for B and V for C, or V(B) / V(C), as a function of M(B) and M(C), where M(B) is molecular weight of B and M(C) the molecular weight of C : Graham's Law of Diffusion.

1 Answers  

---

print a pattern of abcdcba abc cba ab ba a a ab ba abc cba abcdcba

0 Answers  

---

all subject of chemical engg

1 Answers  

---

Question 75 - The molecular weights M in kg / mol of 3 different monomers a, b and c in a polymer are Ma = 14, Mb = 16 and Mc = 18. The fraction of polymer chain X of 3 different monomers a, b and c in a polymer are Xa = 0.5, Xb = 0.3 and Xc = 0.2. (i) Calculate number average molecular weight by using the formula Ma Xa + Mb Xb + Mc Xc. (ii) Calculate weight average molecular weight by using the formula (Ma Xa Ma + Mb Xb Mb + Mc Xc Mc) / (Ma Xa + Mb Xb + Mc Xc). (iii) Calculate the polydispersity by using the answer in (ii) divided by answer in (i). (iv) If the molecular weight of repeat unit is 12, calculate the degree of polymerization by using the formula (Ma Xa + Mb Xb + Mc Xc) / (molecular weight of repeat unit).

1 Answers  

---

What is a good device to use for obtaining viscosity data for a non-newtonian fluid?

0 Answers  

---

I HAVE BEEN SELECTED FOR IOCL PANIPAT INTERVIEW,ACCTUALLY IAM DOING APPRENTIES TRAINEE IN CPCL.IAM GOING TO ATTEND THE IOCL PANIPAT INTERVIEW.SO PLEASE HELP ME HOW I PREPARE FOR INTERVIEW BY SUBJECT AND ALSO BY FIELD.

0 Answers   IOCL,

---