What are the procedures of starting of diesel engine?

Question Posted / pintu9774689249

4 Answers
7267 Views
I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

What are the procedures of starting of diesel engine?..

Answer / gurmeet singh majitha

by rotating its flywheel which is driectly mounted on
crankshaft. when crank shaft will rotate, it give power to
cam shaft as well injecting pump. engine piston and
cylinder will suck air in suction stroke and compres it on
high temp. when fuel injector pump will spray fuel ignition
will take place and engine wil come in working

Is This Answer Correct ?

6 Yes

1 No

What are the procedures of starting of diesel engine?..

Answer / narayan sharma

PROCEDURE TO START THE DIESLE ENGINE, WHEN WE ROTATE WHEEL
CONNECTED TO THE ENGINE DRIVING SHAFT MANUALY OR
ELECTRICALLY THEN PISTON MOVES UPWARD AND AIR IN CYLINDER
COMPRESS AT HIGH PRESS. AND TEMP.,THEN PUMP INJECT FUEL IN
THE CYLINDER AND BURNS THIS CYCLE REPEATED CONT.............

Is This Answer Correct ?

0 Yes

0 No

What are the procedures of starting of diesel engine?..

Answer / vijee

Dear my friends
whenever want to start the eng, first of all we have to
check the eng whether it cant be start or not. before start
the eng check the lube oil in sump,water in radiator,
check the connection of electricals,check the load (it
should be disconnected),if its air starting eng, check the
starting air pressure as sufficient. then only u can start
the eng. it just small things for small engs.

Is This Answer Correct ?

0 Yes

2 No

What are the procedures of starting of diesel engine?..

Answer / kaja najmudeen.s

efficiency is morethan other engine i.e 87%.

Is This Answer Correct ?

1 Yes

5 No

Post New Answer

More Mechanical Engineering Interview Questions

What are the causes of emergency stop in a steam engine?

0 Answers ABC Inc, RRB, Siemens,

why we do not megger to motor under system is very high vaccum condition. and what is the tempreture of vaccum conditon

0 Answers Daikin,

Is heat treatment required for hardox 400+Mild steel welding ?

2 Answers

What are the flow characteristics?

0 Answers

Zimbobwe was formerly known as

0 Answers RRB,

what is little law and why it is so called?

1 Answers GATE,

if outer diameter of pipe is known how to determine the inner diameter of pipe????

4 Answers Hetero,

i am prepared for the rrb section engineer, please help me to guide , how to prepare and which books are good for technical, aptitude(arthimetic, resonning and g.k), send details to me by email: sudhakar.gudditi@gmail.com

1 Answers

dear sir i m anshul kumar from dehradun i want to last five year railway chandigarh and allahabd entrance exam papers pls send it on my id my id is anshuldhiman83@gmail.com or anshuldhiman@rediffmail.com i shall be very greatful to u thank u

0 Answers

Explain the difference between grey iron and white iron. What is mottled iron ?

0 Answers

Wasco Interview 1-the type of transducer that convert mechanical movement into a voltage 2-pump 2500 psi and 100 MG select it 3-modes of heat transfer 4-the difference bet PSIA and PSIG 5-the function of relief valve and no return valve (check valve ) 6-types of bearing general catogires 7-function of bearing 8-compressor surge 9-pump cavitation 10-define critical speed 11-compression ratio decease volumetric ratio ........... 12-using inter-cooling in multi stage compressors to ....... 13-using cascade system in refrigerator function ? 14-define performance and efficiency .

0 Answers

can you please give me the questions related to steels,i have an interview regarding to steels factory

0 Answers

For more Mechanical Engineering Interview Questions Click Here