what is uplink port why are we use this port,this port having extra feature or only use to redundant link or other please explain it ,,,,,,,,,,,,,,,, bcz i am very confuse ..... Thanks

any body can send me CCNA voice simulator practice exam software.

hi shyam i am putting urs question here I am facing one problem in my layer 2 switch I don’t know the problem is on switch side or client side. The problem is some PC (not all) are stop participate in LAN they don’t send or recd. Packet from switch and if I check RJ45 (with LAN tester)from PC side the packet and 8 pin wire is working fine and after that process of LAN tester I plug RJ 45 in PC now PC start recd/ send packets what is the problem I don’t understand even client side no virus found RJ45 is ok and switch has no problem bcoz other PC is working fine Cable (cat 5 ) is also fine bcoz I didn’t crimp again just check in LAN tester and start working fine. Plz any one solve this matter. And after lan tester process pc is working fine and after 2 or 3 hour it again start same problem and again same process lan tester I have used

IBM,

frends i am suffring from newfolder.exe virus in my server 2000 win how i have to remove it plz help me Jitendera sinha

what is different between cisco router and layer 3 switch

Cisco, LABA Nepal,

what is stub router

Satyam,

I have one problem in my network my windows xp pc in workgroup there r 2 NIC card one I have disable in and second is active. The problem is in a day some time its ip conflict with other and when I see the event log and get the conflict ip mac and scan it with LAN scanner on one is there for that mac address nic in my network I have disable dhcp also don’t know what is the problem

hi i am facing one problem.ptoblem is like that i am getting output error on mine router ethernet interfae here is the cisco#show interface e0 Ethernet0 is up, line protocol is up Hardware is QUICC Ethernet, address is 0030.802d.2a17 (bia 0030.802d.2a17) Internet address is 202.122.20.225/28 MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec) ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:00, output 00:00:00, output hang never Last clearing of "show interface" counters 05:55:07 Queueing strategy: fifo Output queue 0/40, 0 drops; input queue 0/75, 0 drops 5 minute input rate 10000 bits/sec, 11 packets/sec 5 minute output rate 29000 bits/sec, 11 packets/sec 1515202 packets input, 359100396 bytes, 1 no buffer Received 6 broadcasts, 0 runts, 0 giants, 1 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 0 input packets with dribble condition detected 1584394 packets output, 1623395338 bytes, 0 underruns 1820 output errors, 26732 collisions, 0 interface resets 0 babbles, 0 late collision, 9698 deferred 18 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out output cisco# what is the reason how to solve this please tell me i am using cisco asa 5520 behid mine internet router and no error on the asa inside interface

Wnat do you know about zenpeck

How convergence happen in ospf?

TCS,

What hppends when ping 127.0.0.1 command executes?

CMS, Wipro,

HI friends mine one of the friends have ask a good question i also donot know the answer so i am putting here Please poet the answer no matter it is wright or wrong put yours view here The question is like that when we are going to configure ospf then there are three way 1st way router ospf 10 netwrok 192.168.1.0 0.0.0.255 area 0 network 192.168.2.0 0.0.0.255 area 0 the 2nd way is like that router ospf 10 netwrok 192.168.0.0 0.0.255.255 area 0 but he inrodused the thrird way like router ospf 10 netwrok 192.168.00000001.0 < ?.?.?.?>area 0 router ospf 10 netwrok 192.168.00000010 area 0 now problem is that what should i put the mask in this way so i puted ? sign Please solve this problem i think this is good one plz donot see for answer please contribute any thing i am reqesting Than you Jitendera kuamr sinha

what is default route

How broadcast is created in switch

what is the reason for creating vlans