Interested to Buy Any Domain ? << Click Here >> for more details...
What is A Check, B Check, C Check & D Check for Diesel
Generators?
- 1 Answers
- 3261 Views
- ISG, I also Faced
- E-Mail Answers
Answer Posted / amit kumar
A-Check (Daily routein Check)
1. Check oil level.
2. Check cleanliness of DG
3. Check Battery Voltage
4. Check any Leakage
5. Check all filter condition
6. Check oil Level
7. Check coolent Level
8. Check Check V-Belt condition
B-Check (Every 300- 350 Hrs.)
1. Change oil.
2. Change oil filter,fuel filter,bypass filter.
3. Change Air Filter.
4. Change water Separator
5. Radiator cleaning with chamical
C-Check (Every 800-1500 Hrs.)
1. Change oil.
2. Change oil filter,fuel filter,bypass filter.
3. Change Air Filter.
4. Change water Separator
5. Radiator cleaning with chamical
6. Check All Electrical terminal & thimbles
7. Check polution level
D-check (Every 3000- 5000 Hrs.)
1. Complete DG set should be dismental.
2. Turbo charger service
3. Injector Pin service
4. Cylinder Head service
5. PT Pump sevice &
6. Repeat same B-Check process.
If your DG set running hours more than 10,000 then in D-
Check You should need to be
1. Change Piston Bearing,
2. Change nozels,
3. Piston Cylinder also need to be change.
4. Change Canopy filter if require
5. Check polution level
| Is This Answer Correct ? | 0 Yes | 0 No |
Post New Answer View All Answers
"What do you going to observe, when a diesel engine is running?"
Hello i am appearing for the BHAVINI written exam 2014 for the post of Technical Officer(Mechanical). Can anyone tell me what topics to prepare?
What is a vee used for on the vee block?
What is ferrite material and explain its applications?
CAN ANY ONE TELL ME WHEN WILL CONDUCT ASSISTANT MOTOR VEHICLE INSPECTOR /RTO APPLICATIONS WILL RELEASE
2. Dry saturated steam at 3.5 bar is expanded through a convergent nozzle to 2.2 bar. The exit area is 5 sq. cm. Calculate the exit velocity and mass flow rate, assuming isentropic expansion and super saturated flow. b) A cast iron cylinder head is fastened to a cylinder of 750mm bore with 12 stud bolts. The maximum pressure inside the cylinder is 3 Mpa. The stiffness of part is thrice the stiffness of the bolt. What should be the initial tightening load so that the point is leak proof at maximum pressure? Also choose a suitable bolt for the above application 2 The propeller shaft of a marine engine is to transmit 600 kW at 1200 rpm, without a significant bending. The efficiency of the propeller is 88% at 32 knots ( 1 knot = 1085 km/hr). If the slenderness ratio is less than 50 and the permissible shear stress should not exceed 65 Mpa. Determine the diameter of shaft. 3 A semi-elliptic leaf spring consists of two extra full-length leaves and six graduated length leaves, including the master leaf. Each leaf is 7.2 mm thick and 65 mm wide. The centre-to-centre distance between the two eyes is 1.3m. The leaves are pre-stressed in such a way that when the load is maximum, stress induced in all leaves are equal to 380 N/mm sq. Determine the maximum force that the spring can withstand
how to calculate GD square for pump?
Purpose of lubricator in a large diesel engine.
can any body sand me previous exampapers of jr. engineer (mechanical)
Name the different shops?
CAN SOMEONE GIVE ME THE LINE DIAGRAM OF A VAPOUR ABSORPTION SYSTEM (VAM)(AIRCONDITIONING)AND A 600 TON CENTRICUGAL AIRCONDITIONING PLANT.
Explain the uses of windmill?
What is mean effective press?
interview questiions for production planning
Why PWHT IS NOT DONE TO STAINLESS STEEL MATERIAL?
