Interested to Buy Any Domain ? << Click Here >> for more details...
What are the safety devices in generator.
- 13 Answers
- 89205 Views
- ABB, Anand Group, ITC Infotech, I also Faced
- E-Mail Answers
Answer Posted / shehzad asgher
None proper installation of NGR
water cercolation pump is tripping In case of Genrator triping
Governor of turbine proper set point according to steam
pressure
Over heat cercoltion water
Low frequency
AVR
| Is This Answer Correct ? | 0 Yes | 1 No |
Post New Answer View All Answers
2. Dry saturated steam at 3.5 bar is expanded through a convergent nozzle to 2.2 bar. The exit area is 5 sq. cm. Calculate the exit velocity and mass flow rate, assuming isentropic expansion and super saturated flow. b) A cast iron cylinder head is fastened to a cylinder of 750mm bore with 12 stud bolts. The maximum pressure inside the cylinder is 3 Mpa. The stiffness of part is thrice the stiffness of the bolt. What should be the initial tightening load so that the point is leak proof at maximum pressure? Also choose a suitable bolt for the above application 2 The propeller shaft of a marine engine is to transmit 600 kW at 1200 rpm, without a significant bending. The efficiency of the propeller is 88% at 32 knots ( 1 knot = 1085 km/hr). If the slenderness ratio is less than 50 and the permissible shear stress should not exceed 65 Mpa. Determine the diameter of shaft. 3 A semi-elliptic leaf spring consists of two extra full-length leaves and six graduated length leaves, including the master leaf. Each leaf is 7.2 mm thick and 65 mm wide. The centre-to-centre distance between the two eyes is 1.3m. The leaves are pre-stressed in such a way that when the load is maximum, stress induced in all leaves are equal to 380 N/mm sq. Determine the maximum force that the spring can withstand
What is knurling?
why not soot blowing performed of air preheater, while soot blower is in retract position?
what is critical temprature discuss that is any pressure greater than critical pressure is valid for boiler design.....2 in what cycle steam power plant is based draw h-s diagram.different process to make gear what is tooth profile what is generatic and directric and many more as i m doing mtech thats why interview was of 30 minute...........
pls, send me jindal steels & power aptitude ques
book name for the written test of rrb exam
hi,i am sekar.i am prepareing Assistant Motor Vehicle Inspector in TN.Transport ,if any one have previous year model pares or some questions,pls send me at gpsekar2007@gmail.com.
Hi, I am Jose. I am an Mehcanical Engineer. I am planning to appear for BHEL ET exam.Can any one help me how to prepare fo this test? Is there any question paper pattern for this test?
sir,i appllied junier engineer engineer in rrb chennai,i need syllabus for the topic of apptitude,reasonong,general english and mechanical engineering,and general studies.please sent my mail id aravindaptc@yahoo.co.in.
How to give the answer for Expected CTC for MNC as well as for growing company?
Dear all, Will some one help me in this issue please? We are entering the Zero Stock Component in Maintenance Order, and we make a Check when the order creator is going to release system will appear Error, until he will not delete that zero stock components from the Maintenance order. but right now what the order creator is not releasing the order but he is going to save order, when's he save the order without release system will generate Reservation in the back ground, which should not happen for Zero Stock Components ? I need the way which we are doing in MB21, Reservation creation by thru Cost Center / WBS Element. At present if you run MB21 and you are going to issue the material system will not allow to generate the reservation if there are zero stock components in the list. please guide me for this issue ? Note : Simple what I need is I don't want to create any reservation thru maintenance order for the Zero Stock Components. Regards, Abdul Mujeeb
what will be the minimum bearing clearance that after it will not profitable for machines?
Explain the fresh water cooling system.
What are the different types of bearings?
HOW MANY PSI CAN REACH THE SCHEDULE 20,40,80 PIPES? GI,BI (CAPACITY OF PIPES)
