Interested to Buy Any Domain ? << Click Here >> for more details...
Hai friends I have dought for O2 analyser how to working in boiler area. And what is the basic principles
- 2 Answers
- 4462 Views
- Enmas, I also Faced
- E-Mail Answers
Answer Posted / rambalaji
1. zirconia oxygen analyzers determine oxygen concentration using the conductivity of a zirconia ceramic cell. Zirconia ceramic cells only allow oxygen ions to pass through at high temperatures (750oC). With reference gas on one side and sample gas on the other, oxygen ions move from the side with the highest concentration of oxygen to that with the lowest concentration. The movement of ions generates an EMF (Electro Motive Force) which can be measured to determine the oxygen content
2. The sensor does not actually measure oxygen concentration, but rather the difference between the amount of oxygen in the flue gas and the amount of oxygen in the air. Rich mixture causes an oxygen demand. this demand Causes high voltage to build up due to transportation of oxygen ions through the sensor layer. Lean mixture causes low voltage since there is oxygen Excess. Sensor working in Nernst Principle
In flue gas side O2 is low : High Voltage
In flue gas side O2 is high : Low Voltage
High Concentration : O2 + 4 e 2O2 -
Low Concentration : 2O2 - O2 + 4 e
0% O2 = 0.82 mv
5% O2 = 0.40 mv
21% O2 = 0 mv
| Is This Answer Correct ? | 4 Yes | 0 No |
Post New Answer View All Answers
Specify ideal accuracy of flow element like orifice plate, Ventury, Annubar. Ultrasonic flow meter etc.
How to Calibrate Coriolis Flow transmitter in field
Q-Explain the different load conditions that will produced different offset which may or may not be acceptable to thhe control function
Why flow/pressure transmitter before control valve?
Can any one send me IOCL instrumentation question papers.. i dont know the pattern of the questions and what to prepare can any one help me on this .. my email id is anwarnishil@gmail.com
dear friends, i have seen flow as the selection critriea in presure guage (bourdon tube) and i would like to know what is the relation between flow and performance of pressure guage other parameters i found in the data sheet are pressure max. 1ksc temperature max. - 50 deg c line size - 80NB operating range - 1ksc pr. guage range - 0-2 ksc thank u,
why we use 3 wire rtd direct wiring for temperature measurement instead of temperature transmitter like bearing temperature
where i can get training in INTOOLS and PDMS in Delhi-NCR OR north part of India. please reply with ur ans. at arunsamkaria@ymail.com
i have used level transmitter in starch cooking preparation tank. tank total height 2mtr.sometime LT display shows some error value when tank is fully empty and diaphragm side i already checked okay no problem in diaphragm area. field cable checked 24volt and mA shows correct value while tank empty mA is 4mA. 4mA i needed that 0% but display showing 10% or 15% percentage values are varying continously please give any good solution for me.....
We Have Two Field bus Pressure Transmitters of Different Sensor Range (I.E One is of Lower range and Another is of Higher Range).Is same Process Line. My Question is Can i provide Saturation Limit to my field Bus Transmitter as We can provide Saturation current limit to HART Instruments. As During Low Pressure Both Working OK ,But During High Pressure, transmitter with Lower sensor range Goes to Fault mode as Beyond its Sensor Limit it can Measure, So may I provide Saturation point Some where to Suppress This Fault during High Pressure.
our kks tagging is crossing more than 12 character please suggest how to take tags in the DCS
Which topics are covered in Process Control?
line up procedure for dp type flow transmitter?
Derive capacitance to 4-20ma conversion formula / relation in capacitance type pressure sensor?
find the kp ki kd from the transper function G(S)=29.44s+04707/1.5349s2+s
