Interested to Buy Any Domain ? << Click Here >> for more details...
what is excitation system explain in detail with its
working?
- 1 Answers
- 8336 Views
- Toshiba, I also Faced
- E-Mail Answers
Answer Posted / mike
1) A.C. excitation.
This type of the exciter operated with a.c. supply and rated frequency around 50 until 250 Hz.The output provide with slip ring to be rectified for internal mounted diode cubicles.This types can replaced for commutator on the d.c with solid state rectifier.
The output from rectifier supply to the generator rotor with slip ring for the d.c excitation system. Usually a pilot exciter made from a permanent magnet for supply to main exciter.
For the main exciter,it commonly made in three phase used the combination of diode in a bridge formation.The bridge arm have a several piece of diodes in parallel condition.
The method for short circuit protection is each diode individually fused to remove it from the electrical circuit in when it happen.
2) Brushless excitation.
This excitation system have a similar function between A.C excitation with advance application.The rectifier diode installed on the exciter shaft.The main exciter has its output armature winding on the rotor with its field on the stator.
Normally for rotor output frequency rated around 100 and 250 Hz and it is connected to the shaft mounted diodes.The rotor of main generator can supply the output with directly application.
The pilot exciter can be a permanent magnet generator with frequency operation until 400 Hz.For the small generator,supply can provide from generator terminal to the exciter field.
3) Thyristor excitation.
For this type of excitation system it used thyristor rectifier to directly control the generator filed current and it can response with faster system by controlling the exciter field current.Thyristor excitation fed system is necessary to provide slip rings and brushes to connect to the machine rotor.
This function is important to alert and response to the error or faulty for system stability due to critical application.But it have disadvantage because this system not been developed commercially and not common system for generator at around the world.It also difficult to providing the reliably control signals to them from stationary equipment.
Excitation power may be provided with direct application to the coupled main and pilot exciters or it can fed from main generator terminals using a step down transformer.
Normally the transformer ratio is design to provide full output during the occurrence of a system fault and it reduces the machine terminal voltage for protection system.
| Is This Answer Correct ? | 2 Yes | 0 No |
Post New Answer View All Answers
what happen when we add mentos in cold drink?& why?
i need the curve duty cycle and amper for (150 kva @50% dyty cycle) transformer turn ratio :19 and vin 400
What is your acheivements
what is 3rd Harmonics? how it is generated in alternator
What are the site acceptance tests for power cables, DG Sets, LT panels & 30kVA UPS ?
What is the necessary and sufficient condition for stability.
we have 3 single phase transformers. how will we generate 6 supply from 3 phase supply input
condition Autotrip facia come on control panel of electrical transmission line?
how we design a pannel to start 10HP motor with the help of star delta starter?
Dear friends I want to design busbar for1600 kva transformer(i.e2100 amps) what are all the factors to be considered before selectinga busbar what are all the standard sizes of busbars what is the formula for finding current of copper and aluminium busbar
How a capacitor discharge weld power supply works? what is the use of a pulse transformer?
IF I KNOW THE AREA OF CROSS SECTION OFTHE WIRE , WATTAGE OF THE LOAD ,VOLTAGE SUPPLY WHAT IM GIVING TO THE LOAD AND ALSO POWER FACTOR OF LOAD ....... SO GIVE ME FOR WHAT AMOUNT OF CURRENT I SHOULD USE WHICH TYPE OF CABLE?
explain the what is a drive ? 0 4 which type motor r use in the celling fan..... PCB plannet 2 13 If stator & rotor of a 3-phase induction motor have different no. of poles, will the motor run or not?? types of drives Why dc supply is used for closing and tripping coil of ht breakers. What happen if we use only ups ac supply only. ACC 1 41 how the 3phase induction motor is running in 2phase supply with help of capacitor? 1 33 what is the actual difference betwen constructional details and constructional features? 1 20 how does commutator convert a.c to d.c?
How can ou verify the size of conductor 50Sq.mm ACSR
Explain the advantages and disadvantages of thermal power plant?
