Interested to Buy Any Domain ? << Click Here >> for more details...
What is the generating voltage of a power station consided
generally?
- 20 Answers
- 40291 Views
- L&T, I also Faced
- E-Mail Answers
Answer Posted / v.swathanthra babu
11KV MAY BE OPTIMUM CONSIDERING COIL SIZE AND INSULATION COST. i.e., for particular range of capacity the generating voltage is less than 11KV means current level high in turns coil size will increase, generator size and cost also goes up. In vise versa generation voltage more than 11KV winding insulation cost may go up. Generator Capacity ranges from 10 to 110 MW the machines sized for 11KV which may be optimum and economical on considering efficiency of machine, cost and transportability limits.
| Is This Answer Correct ? | 1 Yes | 0 No |
Post New Answer View All Answers
How can claculate to attain the desired PF in the line ( HOW Much KVAR is required ) Pls Give the formula? Equate Petrochemical 0 1 how to calculate sizing of NGTR (Transformer rating,Loading resistor value and Current rating of resistor) and what is the X/R ratio. Details : 11kV,Capacitance 1.73532 micro farads,40kA for 1sec. 0 1 What will happened. if we feed 3phase supplay to the stater with out insert the rotor. How much current will flow through the stater winnding? Equate Petrochemical 0 1 What is required of exietation to the alternater. 0 1 why star point of HT motor not earthed? Equate Petrochemical 0 1 Why we are getting low voltage in star connection? Equate Petrochemical 0 2 What's ND relay & it's functions? Equate Petrochemical 0 2 How instantanious short circuit current is calculated? its formula? Equate Petrochemical 0 2 What is servo Motor? What's the advantages of this motor over Induction motor? Equate Petrochemical 0 2 What is core CT & it's function? Equate Petrochemical 0 3 what is meant by star/delta voltages as 440/220 in a 3 phase induction motor, and why it should be connected on STAR IN 3 PHASE SUPPLY L & T 0 4 What is required of exietation to the alternater. KNB 1 23 what is the design voltage for 6.6KV 2000 KVAR HT capacitor? Consultancy 0 3 Pls explain about vfd control?Where it is used, Give some example? siemens 1 22 Please explain me abt PQ diagaram in the power sector. 0 9
how the works electronic energy meter?
3- What is the target from Zero Impedance, Single Phase Imp., S/C Imp. and magnetic balance tests?
v/f drive basic princeple
A 100W electric lamp is supplied from a 115V, 60HZ source. The peak instantaneous power dissipated in the lamp filament is
If a rotary UPS is in line through grid power; What would be the impact on Power Factor if the load through rotary ups is 25% , 50% , 75% & 100%. Will the power factor reduce with less load?
In power transmission using open belts or horizontal shafts it is preferable to have the slack side of the belt on the top because
why the electrolyte level in lead acid battery is maintained 2.5 cms above electrodes?
how to meas-our losses for L.T & H.T
sir i completed apprentice in TNEB.apprentice is eligible for 'c' licence
Why i receive the GCU fault in my DG Sychronization panel . what all the factors considered for this fault .
In Generator How suction compression power and exhaust works ?
Is MEN and RCD related to each other ?? IF yes then how??
what is Insulation monitoring device. where it is used? (in switchgear room or control panel or in field equipment)
george phenomenon of synchronous machine
