why does not tester light up when it is touched to neutral of
3 pin socket.
- 4 Answers
- 18329 Views
- I also Faced
- E-Mail Answers
Answer Posted / ankamsreekar
The practical line testers are works for the voltages above
150v. The return path is earth (land surface) via human body.
When you touched to line the voltage across the tester is
230v. If you touched to neutral the voltage across the
tester is in order of 2-10V depending up on the conditions
of distribution transformer.
so the tester will not work.
| Is This Answer Correct ? | 10 Yes | 2 No |
Post New Answer View All Answers
What is the formulae of Megger value for a A.C.Motor
I need HT sphere gap calibration table. Can any body help me.
1.what is the difference between ct and cvt? 2.what is the difference between pt and cvt? 3.what is the difference between relays and circuit breakers?
i karmveer bharti persuing b.tech . plz send me syllabus and name of reference books. for preparation of section eng.
What is the effect of positive feedback on the stability of the systems?
Is a contactor (or master relay) required between incoming lines and a VFD? The question goes to safety. If a contactor were used before the VFD and an e-stop engaged then the motor will coast to a stop (i.e. VFD loses power) instead of stopping much faster if the VFD braking fucntion were used. It would make more sense to keep power on the VFD.
what the principle of sincroscope?how it works?when it needed?
would you please give me any idea about the BARC interview question on electrical? i have an interview on 1st july.....plz hlp me.......its urgent......
How will you utilise electrical power? You can start from the generating station.
why current is constant on d.c?
hi if anybody got model questions for cpcl Grade'A' electrical engineer position.send it to my mail please krishkumar22@gmail.com
Dear all, I just want to ask an expert on this forum for some insights. For the magnetic balance test, when applied voltage on a Delta-Star transformer e.g. Dyn11, the following relationships apply for HV side: 1. H1-H2 = H2-H3 H3-H1 2. H2-H3 = H3-H1 H1-H2 3. H3-H1 = H1-H2 H2-H3 For the LV side also: 4. X1-X0 = X2-X0 X3-X0 5. X2-X0 = X3-X0 X1-X0 6. X3-X0 = X1-X0 X2-X0 Is there a similar pattern for Y-d, Y-Y, D-d? And how about Y-z, D-z, Z-y transformers? I've tested a YNzn5 transformer and for LV side I don't see the pattern. In this particular case I got for LV side the following (see values below): H1-H0 H2-H0 H3-H0 X0-X1 X0-X2 X0-X3 128.0 119.9 7.2 29.2 13.3 15.8 70.7 128.4 59.2 23.4 22.0 3.6 7.2 120.1 128.1 13.4 29.3 15.8 What is the relationship here for LV? For row 1 I see the relationship, for row 3 I also see but it's shifted, but for row 2 I don't see such relationship. Any suggestions, answers, someone?
why 1.7Uo for HV cable Hi pot test?IE standard why?
Sir, I have applied for the of Assistant.engineer of NPDCL. please send me all AP TRANSCO AND JENCO solved papers of previous exams . I requested send me the papers to my id as soon as possible (rajanikanth_peddi@yahoo.co.in) (This is very urgent) Thank You,
what is meant by poly phase induction motor ? how its operating by single phase or three phase?
