Interested to Buy Any Domain ? << Click Here >> for more details...
What happens if a three phase induction motor is suddenly
single-phased while running? Which type of winding
connection will be affected?
- 22 Answers
- 72021 Views
- B4S Solutions, DRDO, FACT, SL Electricals, I also Faced
- E-Mail Answers
Answer Posted / syed
Three phase motor suddenly runing single or two phase.Motor
will get over heat and giving noise.this case if we have
protection like breacker it will trip other wise motor will
burn out
| Is This Answer Correct ? | 19 Yes | 3 No |
Post New Answer View All Answers
1. If 8.35%Z means the percentage impedance of 132kV-line from power company, we will like to reconfirm its base capacity.
Define gain margin?
how to calculate the lightning arrester conductor @ no of earth pits required
what is the isolation transformer. what is the isolator?
draw the restricted earth fault protection circuit install on power transformer and identify its parameters and draw C/C curve of it
what is mean by D.O. in distribution line poles?
Please, if 1kw is equal to 1.25kva; how then do I know how many kva in 7.5kw?
1. A 380 / 220 V r.m.s. 3-phase 4-wire circuit carries loads of 8 + j8.1 ohm; 4 + j4.1 ohm; and 2 +j2.1 ohmin the three phases respectively. The length of the circuit is 100 m, and the resistivity of the phase conductors is 0.0005 Ω/m. The neutral conductor is of the same size as the phase conductors. a) Select a reference angle 0for the first phase. Then write down the three phase voltages in both polar format and complex number format. b) Make appropriate assumptions, and take temperature effects on resistance is insignificant. Calculate the currents in the three phases. (Note: Determine conductor resistance, and apply Kirchhoff’s Voltage Law) Based on the result, suggest a main switch rating for the circuit. c) Show your preferred direction of neutral current in a diagram, and then determine its value. (Note: Apply superposition principle, and Kirchhoff’s Current Law) Use its magnitude to show that in this circuit, the unbalanced load may increase the voltage drop in some of the phases. (Note: Also observe the common volt drip in neutral) State your assumptions, if there are any. d) Suddenly the neutral wire of the circuit is broken. Estimate the new currents in the first phase, i.e. Phase L1. State your assumptions, if there are any.
1)what is the function of a frequency inverter? 2)If a few frequency inverter are connected onto a device network,what are the two setting that will ensure the frequency inverter work properly on the network. 3)whats is the name of the input sensor for weigher? 4)How to confirm that the load cellis faulty? 5)Describe briefly the steps to validate that the weigher is working properly? 6)Describe the procedure to validate the flowmeter accuracy? 7)Describe briefly the steps to validate that the tempreture sensor/transformer is working properly. 8)what is the adjustment that need to be done when you are calibrating the temperature transmitter ? 9)what are the safety measures to be taken before disconnecting motor for rewinding. 10)whats is the synchronous speed in rpm of typical 4pole 50hz motor? 11)whats is the formula for kw, ohm's law 12)if a 3phase motor is rated 3kw,415vac,what is it's rated ampere?
If the Brush of DC motor is shifted by 90 deg, then what happens to voltage and torque? Both voltage and torque are zero. how to justify the answer?
why do you add the load short circuit impedance when considering short circuit amperage. It seems that you should only consider supply. If you need to consider loads and you don't know what loads are to be added , what would be a good sub-transient reactance rating for the loads?
can anybody send me syllabus of rrb section engg (electrical). and also send previous question pepar...
what is difference between speed mode and torque mode in motor?? explain in simple words please.
If a transformer primary winding operates at 240v, the secondary at 120v and the load is 1500w & the transformer is rated at 92% efficient, what's the current flowing through the primary winding of the transformer? What is the formula for finding this?
how flow current in 220 kv line to line
