Interested to Buy Any Domain ? << Click Here >> for more details...
We have ZR22G-100-S-A-E-T-T--E-A/CV/F1 Model Zirconia
Oxygen analyser which is Yokogawa make. I kept the analyser
in Flue gas path at Air pre heater area. My plant is 7.5MW
Biomass power plant. For a particular fuel, Coconut Husk
which contains Sodium and Potassium chlorides iam not
getting proper reading, Analyser output always Zero. I
calibrated the analyser and it is OK. For Other fuels like
Wood chips, Cholam waste, DOB, Groundnutshells, Ply wood
waste and all iam getting actual percentage of Oxygen. What
is the main reason behind this draw back?
- 2 Answers
- 6333 Views
- I also Faced
- E-Mail Answers
Answer Posted / haresh mod
Pls. set your fuel temperature bcs. normally zirconia o2 analyzer work on 800-900 deg. centigrade temperature.
So set the temp. still you not get result then pls regulate your flow and also with your process gas you have to ptovide atmospheric air with set pressure(>=1kg/cm2).
| Is This Answer Correct ? | 5 Yes | 0 No |
Post New Answer View All Answers
What is the difference between PLC and DDC?
I want to buy a seal kit of a pneumatic power cylinder.But I don't know it's specification.So please help me to know its specification.
send me last 5 years questions asked in rrb chennai, for section engineer
In turbine what does term CDP, NI, NH, HSSOC means.
What is Erosion in a control valve?
Where are oxygen analysers installed in cfbc boilers? What are their usual readings?
please any body have most important data for study for saudi aramco test of instrument QC thanks email shahnaveedullah@gmail.com
1.what is the effect of vapour presuure in orifice plate flow measurement 2.which is more effective 2 pressure sensors or one single differential pressure sensor in orifice plate measurement 3.how to design a v/i converter and i/v converter 4.how many type of thermocouple are there 5.how many leads are there in thermocouple measurement 6.how pressure sensors are connected in level measurement in differential pressure method 7.what is the output of capacitive pressure sensor (ac or dc),how its o/p is signal charactarized 8.what is the physical meaning of discharge coeeficient,why it is calculated,orifice plate what is its value,why it is less than 1,Q at upstream is equal to or not equal to Q at downstream of orifice plate why?what is vena contracta in orifice plate 9.why rotameter is called variable area flowmeter,it can measure flow even if area is not varying,why it is made tapered 10.design a 10 bit counter ,which counter you will prefer 11.how to remove self heating error in RTD 12.which is more sensitive pt100 or pt50 13.why thermocouple are connected in parallel 14.what is lead contact error in RTD,how to avoid 15.what is P,PI,PID,PD controller,why there is no ID controller 16.what is override,split range,sequential,ratio,feedforward,cascade controller 17.why we moved from SR to JK and then JK to master slave JK flipflop,give correct reason 18.how to measure level of a closed container which contains vapour and liquid,remember no vapour gas should be leaked,so ultrasonic and capacitive is not an option,design another method 19.how to design horse race counter including sensors and signal conditioning element 20.what is bevelling
Can any one tell me what type of question asked for instrumentation and control interview panel??? pls mail ramashankar.goel@gmail.com
Explain signal isolator
explain key exchanges in all security modes WPA,WPA2,TLS?
what is the importance of CV in the control valves? how it is calculated?
There are two chlorination tonners both are connected to two pressure swithes and the pressure switch is connected to SOV which operates the valve to changeover the tonner selection i.e if pressure one tonner goes low the other tonner should come in line if it is inautomatic selection design a circuit using relays ?
Explain why use mmwc unit?
Specific gravity.
