Interested to Buy Any Domain ? << Click Here >> for more details...
In a Circuit how the MCB and Fuse ratings are calculated.
And shall the fuse follws the MCB or it is otherwise?
- 16 Answers
- 91993 Views
- Emerson, HCL, Thirumalai Chemicals, I also Faced
- E-Mail Answers
Answer Posted / daher
the current rating of the fuse must be equal to the load
because the fuses melting point disconnect the circuit if
the current load becomes greater than the specific rating.
in high ruputer capacity fuse,the fuse able to carry1.2
over the rating.meaning 20% more.MCB rating calculation is
to know how mush the consuption load and according to that
cal.we decide the rate of MCB from the catalog rating of
CB, must be more than the load.DONT FORGET THE SHORT
CIRCUIT CALCULATION
| Is This Answer Correct ? | 35 Yes | 13 No |
Post New Answer View All Answers
what is formula for calculate thermal overload in new numiricalrelay( not in bimetal relay)?
What must be the distance between the Earth pit which are grounded from two different sources. Example: Distance between the earth pit for LV Panel-1 & 2
What is clock position of Transformer?what are the clock positions are there?and what is different of them?
what is the Pickup/drop off ratio in BCPU relays
Dear all, I just want to ask an expert on this forum for some insights. For the magnetic balance test, when applied voltage on a Delta-Star transformer e.g. Dyn11, the following relationships apply for HV side: 1. H1-H2 = H2-H3 H3-H1 2. H2-H3 = H3-H1 H1-H2 3. H3-H1 = H1-H2 H2-H3 For the LV side also: 4. X1-X0 = X2-X0 X3-X0 5. X2-X0 = X3-X0 X1-X0 6. X3-X0 = X1-X0 X2-X0 Is there a similar pattern for Y-d, Y-Y, D-d? And how about Y-z, D-z, Z-y transformers? I've tested a YNzn5 transformer and for LV side I don't see the pattern. In this particular case I got for LV side the following (see values below): H1-H0 H2-H0 H3-H0 X0-X1 X0-X2 X0-X3 128.0 119.9 7.2 29.2 13.3 15.8 70.7 128.4 59.2 23.4 22.0 3.6 7.2 120.1 128.1 13.4 29.3 15.8 What is the relationship here for LV? For row 1 I see the relationship, for row 3 I also see but it's shifted, but for row 2 I don't see such relationship. Any suggestions, answers, someone?
why Lightning arrestor are made by 2 seperate stack of inslutor but why cvt are in single stack of insulator.
explain working principle of earth leakage relay
Why dry type cast resin transformers tap link blast in HV side while power shut down times on load?
what is the basic need of domestic loads 1- voltage 2- current
How to calculate VA rating for CT or PT or Control Transformer?
Which Class insulation is prefered for the sandwich Busducts ? Why?
what is formula to cal cute earth pit numbers and size of earth strip used in earthing?
explain the what is a drive ? 0 4 which type motor r use in the celling fan..... PCB plannet 2 13 If stator & rotor of a 3-phase induction motor have different no. of poles, will the motor run or not?? types of drives Why dc supply is used for closing and tripping coil of ht breakers. What happen if we use only ups ac supply only. ACC 1 41 how the 3phase induction motor is running in 2phase supply with help of capacitor? 1 33 what is the actual difference betwen constructional details and constructional features? 1 20 how does commutator convert a.c to d.c?
How impulse levels are calculated that for 11kV impulse is 75kvp, for 24kV impulse is 125kvp ?
WHY RATING OF VCB NOT LESS THAN 630A
