Answer / shahin

Freame Relay is a high performance WAN protocol that
operates at the data link layer of OSI reference model.
Frame raley was introduced to used over ISDN interfaces, but
now a days frame relay is used over a variety of other
interfaces as well.

Frame relay define interconnection between frame relay CPE
(Customer-premises equipment)& frame relay switch. the
connection over carrier network is not define by frame relay.

No, frame relay is not a circuit switch switching
technology. It is used packet switching technology. frame
relay is connection oriented: so a connection must establish
before information can be sent to remote device. This
connection is provided by Virtual Circuit (VC).

Answer / prasanna

frame relay is a packet switched
one to many
wan technology
NBMA(non-broadcast multi access

What command would you use to find out the names of Novell servers on a network? A. show ipx servers B. show ipx hosts C. show ipx sap D. show ipx nodes.

1 Answers  

---

How we put NIC in promiscuous mode when using MS windows, can any one tell me in detail

1 Answers   Cisco, IBM,

---

If i had 400 computers set in a site how many VLAN i should configure so that i can share a proper bandwith,and also i had two lease line connection of 2Mbps each,

1 Answers   IBM,

---

Hi all, suppose more than two network administrators are configure same router with different configuration through telnet at the same time.. then whose(admin's) configuration will use router for routing ?

2 Answers  

---

Which command would configure Interface E0 with an IP address of 12.23.4.5 using a Subnet mask of 255.255.255.0 ? A.) ip address 12.23.4.5 255.255.255.0 B.) ip address 12.23.4.5 /24 C.) ip address 12.23.4.5 mask 255.255.255.0 D.) ip address 12.23.4.5 mask ff:ff:ff:0 E.) that is an invalid mask for a class 'A' address

3 Answers   Wipro,

---

As the system administrator, you enter the following commands at the command prompt: ipx routing access-list 800 permit 2b 4d int e0 ipx network 4d ipx access-group 800 out int e1 ipx network 2b int e2 ipx network 3c What did these command accomplish? A. Traffic from network 4c destined for network 4d will be forwarded out Ethernet0. B. Traffic from network 3c destined for network 4d will be forwarded out Ethernet0. C. Traffic from network 2b destined for network 4d will be forwarded out Ethernet0. D. Traffic from network 4d destined for network 2d will be forwarded out Ethernet0.

1 Answers  

---

Which two statements about a bridge are true? (Choose two) A. A bridge floods multicasts B. A bridge floods broadcasts C. A bridge does not flood multicasts D. A bridge does not flood broadcasts

1 Answers  

---

Classful routing protocols do not include subnet masks in their routing updates. Which of the following routing protocols are considered classful? A.) EIGRP B.) OSPF C.) TCP D.) IGRP E.) RIP F.) IP

2 Answers  

---

Identify the X.25 addressing standard? A.) X.121 B.) X.25a C.) ITU-1 D.) Q933a

1 Answers  

---

We have one router,we r using two routing protocol eigrp 90 net 1.1.1.0/16, ospf 110 net 1.1.1.0/24 on same router, Is it possible?

6 Answers   Wipro,

---

What does the meaning of interface 0/0?

0 Answers  

---

Identify the purpose of the Ping command? A.) Share routing information with a neighbor router B.) Transmit user data when buffers are full C.) Test connectivity at layer 3 D.) Test entire protocol stack

2 Answers  

---