Answer / jitendera kumar sinha

hi,there is no any option so how can i choose any option
but i am trying to do some explanation
1 switch have the multicollision domain and single broadcast
domain.so it can enhance the n/w performance.

2 switches uses csma/cd protocol for comnication.

3 rd and most importance switches uses mac address for there
communication within the n/w rather then ip address so data
transmission is fast,

these are the 3ree basic region that can enhance the n/w
performance

Answer / s.m.feroz ahmed

Hi,

To Improve performance of Ethernet Switch one has to
configure Switch through Console Port and divide the
Network in switch by configuring Fa01 fast Ethernet in
order to improve performance.

Name the command we give if router ios stucked?

0 Answers  

---

What is cisco?

0 Answers  

---

Which OSI Reference Layer controls end-to-end (host to host) communication? A.) Transport B.) Physical C.) Datalink D.) Network E.) Session

1 Answers  

---

What is the 5-4-3-2-1 rule of network design?

3 Answers  

---

Identify the mode reflected by the following prompt 'Router'? A.) Setup B.) RXBoot C.) Boot mode D.) Privileged exec mode

2 Answers   Cisco,

---

1 what is private vlam 2 if there is a router which have two fast Ethernet from from fa0/0 192.168.10.0/24 network is connected from fa0/1 192.168.20.0/24 network is connected all bacsic routing is done will they communicate 3 what is difference between snmp v1 v2 and v3 what difference between name and stranded access list

2 Answers  

---

What are the disadvantages of symmetric algorithms?

0 Answers   CCIE,

---

What is a L2F protocol?

1 Answers   CCIE,

---

What is the IP extended access list range? A.) 1000-1099 B.) 100-199 C.) 1-99 D.) 101-200

4 Answers  

---

In the setup dialog, what do the square brackets indicate? A. current or default spores B. hard coded values that cannot be modified C. values entered by the administrator but not saved D. values that must be written to PAVRAM before becoming enabled

1 Answers  

---

Identify the 2 commands that will display the status and information about interface E0 only? A.) show interface ethernet E0 B.) show interface E0 C.) show E0 D.) show int E0 E.) show interface

1 Answers  

---

hi... i am usin packet tracer 5.0.. i hav connect two routers A and B. A has 200.100.25.100 and 1.0.0.1 and router B has 200.100.50.100 and 1.0.0.2... i hav connected 1.0.0.1 and 1.0.0.2... now i want to route 200.100.25.100 and 200.10.50.100 usin rip.. i enable rip in both the routers... but whn i give the command show ip route... i jus get this Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set A# so can sombody tell me where i hav gone wrong... thanku

1 Answers  

---