Answer / gopal

dynamic host configuration protocal, and it can assign ips
to clients automaticully.

Answer / prasanta ku. meher

In Windows Server 2003 theree is option to make DHCP
server.It it used to provide and configuring IP address to
remote host.
Go to start
>ontrol panal
>add or remove program
>add remove windows component
>network services
>select dhcp-next-next-finish.

Then for configering dhcp >tart
> program
>admin tools
>click on DHCP
On DHCP server wizard there are many options to
configured. Put a velid IP address range.You can reserve
some Ip for specific devieces and exclude some IP address
for future usage.
So hope Now you can configure a DHCP server.

Answer / jj

to set DHCP you need DHCP server or DHCP server capable
device such as cisco router etc... You then set the address
pool and excluded adresses then if it needs to be forwarded
off that lan segment you need to set ip helper on the
recieving interface of the none DHCP server router recieving
the broadcast. You will also need to configure the lease
time and default gateway etc..

Answer / deepak

1-To set DHCP First we need dhcp service that is taken
from start-program-add or remove program-add remove windows
component-network services- select dhcp-next-next-finish.
2-now start- program- admin tool- click on DHCP-r click on
dhcp server - put start ip address as 192.168.0.10 and end
ip address as 192.168.0.100 now follow the simple step if u
want to reserve some ip address u can select reserve option
here a lot of option u can set according to your need.
advantage- it will be provide ip address automatically.

Answer / upendra

go to network place and right click on it and go to
propoties and go to tcpip protocol and set ip
automatically.then automatically set ip address, this is
known as DHCP , this is the way .

Answer / janardan joshi

fist of all when u want to set dhcp on the server side ---

step1- install dhcp by-- from start-seeting -control panal-
add or remove program-add remove windows
component-network services- select dhcp-next-next-finish.

stap 2- configer dhcp--now start- program- admin tool-
click on DHCP-r click on
dhcp server - put start ip address as 192.168.0.10 and end
ip address as 192.168.0.100 now follow the simple step if u
want to reserve some ip address u can select reserve option
here a lot of option u can set according to your need.

advantage- it will be provide ip address automatically.

Answer / soumya

i think if u hav a server os in ur system then go to
windows component in control panel n select networking..
then detail where u will gwt a DHCP server option.. click
it.. it will show u a welcome wizard... configure there n
see will will get a dhcp tool in administrative tools in
all program..

hope i hav given a correct answar

Answer / m chenchu babu

DHCP STAND FOR DYNAMIC HOST CONFIGURAION PROTOCOL IS USE TO
AUTOMATICALL ASSIN THE IP ADDRESSS

Answer / vadirajjr87

Install the service and specify the ip range and start the service . Done :)

Answer / anil

dynamic host configuration protocol(dhcp),port number-67,
must u have server go to servermanager select dhcp create
scope(it is used to the range of ip address)to assin the ip
add automatically to the users
note:- run-cmd->type ipconfig/release press enter
type ipconfig/renew

Do sockets use tcp?

0 Answers  

What is semaphore os?

0 Answers  

Is http based on tcp?

0 Answers  

differnt type of port number and theire uses?

9 Answers   College School Exams Tests, CybAge, IGMP, RDP, TCS,

What is the role of tcp/ip in data transmission from source to destination?

0 Answers  

How to form loop in Rip?and how to avoid the loop?

3 Answers   Anik Industries, HCL,

Is Wifi is the application software or system software

9 Answers  

Explain address resolution protocol arp?

0 Answers  

What is the basics of internet routing?

0 Answers  

what is the difference between layer 2 and layer 3 qos

6 Answers   Ceeyes, HP,

Explain 4 example of application layer?

0 Answers  

How do I check if a port is open on my mac?

0 Answers