Which of the following is an example of the Physical Layer? A.) SQL B.) IP C.) LLC D.) DDP E.) Ethernet

2 Answers  

---

In which two modes can the ICMP ping command be used? (Choose two) A. user B. privileged C. global configuration D. interface configuration

1 Answers  

---

A traffic light is an example of what type of mechanism? A.) Collision detection B.) Flow control C.) Sequence numbering D.) Network management

1 Answers  

---

hi... i am usin packet tracer 5.0.. i hav connect two routers A and B. A has 200.100.25.100 and 1.0.0.1 and router B has 200.100.50.100 and 1.0.0.2... i hav connected 1.0.0.1 and 1.0.0.2... now i want to route 200.100.25.100 and 200.10.50.100 usin rip.. i enable rip in both the routers... but whn i give the command show ip route... i jus get this Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set A# so can sombody tell me where i hav gone wrong... thanku

4 Answers  

---

What is the difference between the communication and transmission?

0 Answers  

---

What is the purpose of Split Horizon? A.) It prevents the regular update messages from reinstating a route that has gone down B.) Information received on an interface cannot be sent back out the same interface C.) Informs all neighbor routers that two routes exist D.) Tells the router the destination is unreachable

1 Answers  

---

Identify 2 features of PPP CHAP authentication? A.) Username and password is sent in clear text B.) Authentication messages are sent periodically during the connection C.) Less secure then PAP D.) Local router 'challenges' the remote router

1 Answers  

---

You have powered on a new router and you want to create an initial configuration. Which mode should you use? A. copy mode B. user mode C. setup mode D. startup mode

4 Answers   Enrich,

---

what is the concept of HA and FA in VPN tunneling?

0 Answers   CCIE,

---

Based upon the 1st octet rule identify the range for a Class A address? A.) 1 - 126 B.) 192 - 223 C.) 128 - 191 D.) 1 - 191

1 Answers  

---

Which OSI layer provides best effort end to end packet delivery? A.) Data-Link B.) Presentation C.) Network D.) Transport E.) Physical F.) Application

3 Answers   Barnes and Noble,

---

here is your question sahin Hi Jitendera, If i m not wrong, then in EIGRP, Metric weight is set to K1(Bandwidth)=1, K2(Delay)=0, K3(Reliability)=1, K4(Load)=0, K5(MTU)=0. This is default setting for EIGRP. I knew about it from ICND 2 cisco press book. Three more questions - a) If we change the K value (I mean metric weight)on a router what will happen??? b) When redistribution is necessary in EIGRP. Is there any condition for that??? c) What is reference bandwidth for metric calculation in EIGRP. As we know, in OSPF, on a CISCO router reference bandwidth is 10Mbps.

3 Answers  

---