Answer / vinay

unable to understand can you expand your question so that i
can understand

Answer / vinay

Thanks man

sorry i don't know the answer if any one knows about it
please post it

thanks

Answer / tarak bhatt

You mean to say all PCs will be connected to ISA server and ISA Server will be connected to router?

In this case communication speed may decrease (loading web page time will increase) due to ISA but bandwidth will remain same.

OR

you mean to say all PCs will be connected to router, ISA server also be connected to router... all PCs will send data to ISA server via router, ... ISA server will verify information and send data to back to Router to send over Internet ?

In this case, your bandwidth and communication speed both will be hurt.

Answer / santosh kumar nayak

If all your systems connected to ISA server and your ISA server is connected to router, there ll not be any issue with the bandwidth. Instead of low bandwidth, your internet speed will became faster than earlier. Because main feature of ISA is to eliminate unwanted traffic in the Network. Also it creates own Cache file(DNS) of frequently accessed pages, which ll reduced the Router overhead and speedup the browsing speed also.

Answer / javid

yes plz i am going to Explain it again.

Hi,we have one gateway which is our Router is interface, now
for the net filtering purpose i would like to set up an ISA
Server,between the router and LAN PCs and assign the ISA
server's IP as gateway for the all PCs. i hope that u can
get it.Thanks in Advance

You have typed "ping" 172.16.101.1 and get the following display: Type escape sequence to abort. Sending 5, 100-byte ICMP Echoes to 172.16.101.1, timeout is 2 seconds: .!!!! What does the "." signify? A. That one message timed out. B. That all messages were successful. C. That one message was successful. D. That one message completed in under the allotted timeframe.

1 Answers  

---

Identify the 2 rules used when configuring a Distance Vector routing protocol? A.) Physically connected network(s) B.) Configure the classfull address, no subnets C.) Enable CDP so neighbors can be detected D.) Same autonomous network

1 Answers  

---

Which is true regarding store-and-forward switching method? A.) Latency varies depending on frame-length B.) Latency is constant C.) It is default for all Cisco switches D.) It only reads the destination hardware address before forwarding the frame

1 Answers  

---

Company XYZ has an employee that works out of the home. The employee runs big client server applications and must quickly transfer large files. The company wants the best cost/benefit on this connection. What would be the most practical solution? A. an ISDN Basic Rate Interface (BRI) connection to the user at home B. a dedicated T1 connection to the user at home C. a dedicated Frame Relay connection to the user at home. D. a standard 28.8 analog dialup connection to the user at home.

1 Answers  

---

Differentiate User Mode from Privileged Mode?

0 Answers  

---

---

Identify the command to configure DLCI 100 on an interface e0? A.) Router(config)# frame-relay local-dlci 100 B.) Router(config)# frame-relay local-dlci 100 int e0 C.) Router(config-if)# frame-relay local-dlci 100 D.) Router(config-if)# frame-relay local-dlci 100 int e0

1 Answers  

---

What is the function of the Transport layer and which protocols reside there? A.) MAC addressing - IP B.) Interhost communication - SQL, NFS C.) Best effort Packet delivery - TCP, UDP D.) End-to-end connections - TCP, UDP

2 Answers  

---

In distance-vector routing, there is a problem known as the 'count to infinity' problem. What is the most direct solution to this? A.) Defining a Maximum. B.) You can not solve the 'count to infinity' problem with a distance vector protocol. C.) Poison Reverse. D.) Triggered Updates. E.) Split Horizon.

2 Answers  

---

Which command enables directly connected network 199.55.72.0 to be used by RIP? A. Router(config router)# rip 199.55.0.0 B. Router(config router)# rip 199.55.72.0 C. Router(config router)# network 199.55.0.0 D. Router(config router)# network 199.55.72.0

1 Answers  

---

Value in which type of access list?

0 Answers  

---

Can you explain different components in PKI?

0 Answers   CCIE,

---

A router on one side of a PPP link uses the resonance RTR1 and the password COPP1-PWD. Which configuration line on RTR1 enables a connection between RTR1 and another router named RTR2? A. username, RTR2 password COPR1-PWD, B. username, RTR1 password COPR1-PWD, C. username, RTR2 password COPR2-PWD, D. username, RTR1 password COPR2-PWD,

1 Answers  

---