Answer / prasad

224.0.0.10

Answer / ankit dhawan

EIGRP always send query reply and acknowladgement as a
unicast packet........EIGRP never sends query reply and
acknowladgement on 224.0.0.10.............it sends these
packets to the ip address of the directly connected
interface as a destination ip address

Answer / jitendera

this is a multicast ip and the ip is
224.0.0.5

What are the 2 functions of the Data Link Mac layer? A.) Handles access to shared media B.) Manages protocol access to the physical network medium C.) Provides SAPs for higher level protocols D.) Allows multiple devices to uniquely identify one another on the data link layer

1 Answers  

---

What is the difference between ‘bit rate’ and ‘baud rate’?

0 Answers  

---

Which device listed below provides clocking for the line? A.) DCE B.) CPE C.) CO D.) DTE E.) Demarc

1 Answers  

---

Hi Gyes There are any sites where we can practice online for ccna exams?Plz let me know because i get time to study in my working hours only

1 Answers  

---

GUY i Have attended one interview for the data craft and they are offering me L1 postion and i am working at l2 in cisco so there is no way to get in the datacraft i am posting here the question he asked to and i have tested the interviewer and i come to know he was not having any knowledge. His questions are-: 1) what is Vlan 2) what is stp and what is difference between stp and RSTP 3) what is HSRP and Diffrence betwwen HSRP and GLBP 4) how to configure HSRP 5) Scenario Based question ( if we have two router and both are connected and there are having redundancy means two interface of the router r1 is connected to the two interface of Router R2 (R1)-------------(R2 (R1)-------------(R2 Now he want to configure the router in such a Manner that if one link down second link should come up.My answer was HSRP and his is "F looting static routing was i wrong "i know F looting Static routing is Theoretically possible but it is not fusible in the scenario where you have multiple router connected to the same router and if you have configured sub interface i challenged him and he lost The Battle and he get angary 5) what the eigrp and how it works 6) tables in eigrp 7) the information of feasible successor where it saved now after answering these all he was very angry ( i can fill the heat) 8) then he come to ospf Area type ( he was also not aware) 9) LSA type and its working ( he was also having confusion ) 10) then is asked routing by rummer( Theroy) 11) hello and dead intervel of EIGRp (theory) 12) Selection cretaria for Eigrp slecting best path ( here we have a long discussion on MTU and he lost the battle and agree That MTU never comes in the accounts in this process) 13) what is ACL type of acl ( here he was aware of TWO type Standard and extended i have told him 5 type( he again get Angry) We have 2hr of discussion and and he told me he will call me latter but i know he never call

1 Answers   IBM,

---

What is the Difference between Switch and Bridge?

9 Answers  

---

What are the steps of data encapsulation?

0 Answers  

---

Which type of LAN segmentation device enables high speed data exchange? A. hub B. bridge C. switch D. repeater

3 Answers   Accenture, TCS,

---

thnx jitender...its me shridh...m working for SG ltd..the situation iz like ths -at a specific time in our company the internet connectivity goes off...v hav two networks in our company...but out of it only one link goes down for 5-10 sec...a fastethernet port becomes down for few sec and automatically becomes Up... Is this occures becoz of Power?? If yes thn y the 2nd network is not affected?? plz tel me jitender how to resolve ths problem? as u sd loop in switch is the primary cause of ths....i wanna know how to resolve it...thnx for ur replys jitender sinha.

2 Answers  

---

Identify the 2 commands the saves the running-config to NVRAM? A.) write memory B.) copy running-config startup-config C.) write network D.) write backup

2 Answers  

---

What three occurrences will reset the holddown timer after a triggered update? A.) Infinity is finally defined as some max number B.) HD Timer expires C.) Another update is received indicating a better metric D.) The router receives a processing task proportional to the number of links in the internetwork E.) The router detects fault LSP's propagating through the internetwork F.) Another update is received indicating net status changed

1 Answers  

---

How many Devices does OSPF & EIGRP Support

5 Answers   HCL,

---