Which command specifies a second subinterface on serial
interface 0?
A. interface s 0.2 point-to-point
B. interface 2 s.0 point-to-point
C. suberinterface 2.s 0 point-to-point
D. interface s 0 sub 2 point-to-point
E. interface s 0.1 point-to-point sub 2
- 2 Answers
- 6076 Views
- I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
How many tables are in ospf protocol?
hi i am facing one problem.ptoblem is like that i am getting output error on mine router ethernet interfae here is the cisco#show interface e0 Ethernet0 is up, line protocol is up Hardware is QUICC Ethernet, address is 0030.802d.2a17 (bia 0030.802d.2a17) Internet address is 202.122.20.225/28 MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec) ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:00, output 00:00:00, output hang never Last clearing of "show interface" counters 05:55:07 Queueing strategy: fifo Output queue 0/40, 0 drops; input queue 0/75, 0 drops 5 minute input rate 10000 bits/sec, 11 packets/sec 5 minute output rate 29000 bits/sec, 11 packets/sec 1515202 packets input, 359100396 bytes, 1 no buffer Received 6 broadcasts, 0 runts, 0 giants, 1 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 0 input packets with dribble condition detected 1584394 packets output, 1623395338 bytes, 0 underruns 1820 output errors, 26732 collisions, 0 interface resets 0 babbles, 0 late collision, 9698 deferred 18 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out output cisco# what is the reason how to solve this please tell me i am using cisco asa 5520 behid mine internet router and no error on the asa inside interface
What are the types of resource sharing?
When discussing static routes, what is the gateway parameter used for? A.) Determining the dynamic route B.) Defining the subnet C.) Defining the Administrative Distance D.) Determining the next hop
Which two statements accurately define IP addressing rules? (Choose two) A. IP multicast addresses start with 240 B. A host Carbon of all 1 a indicates a network broadcast C. The value of zero (0) in the host Carbon means all hosts on the network D. IP addresses are four octets long and contain a network Carbon and a host Carbon
Which two of the following are valid ways to have multiple encapsulation types on a single interface? A.) This is not possible B.) subinterfaces C.) additional physical interfaces D.) secondary addresses
Hi,can anyone explain me in brief about ccna security. waiting for your answer
What is a characteristic of Store and Forward switches? A.) They forward the frame before it is completely read. B.) They work at wire speed. C.) They are the same a Cut-Through switching. D.) They read the entire frame and check CRC before forwarding. E.) They decrease latency.
What is the draw back of ospf protocol?
What would be the first command from global configuration mode to enable RIP on your router for interface E0, with an address of 181.86.4.4 and mask of 255.255.255.0 ? A.) router rip B.) network 181.89.4.0 255.255.255.0 C.) router rip int e0 D.) router rip 181.86.0.0 E.) router rip 181.86.4.0 F.) network 181.86.0.0
Tell me which multicast ip eigrp protocol use?
What is HDLC?
CCNA 
