Answer / guest

Answer: D

The Physical layers deals with synchronizing the 1s and 0s
on the wire.

Which statement is true? A. While bridges are used to segment networks, they will not isolate broadcast or multicast packets. B. A bridge looks at every packet within its network segment and works like a hub re-broadcasting the packet if the destination is within its network segment. C. A bridge maintains a table of the IP addresses of the hosts within its network segment and forwards the packet directly to the destination based upon the IP address. D. A bridge resets the hop count by keeping all packets within the network segment. Only packets addressed to a specific destination host outside the network segment are allowed to pass through the bridge.

1 Answers  

---

How do you configure a cisco router for routing ipx?

0 Answers  

---

Which mathematically form used inipv6?

0 Answers  

---

Which protocol carries messages such as destination Unreachable, Time Exceeded, Parameter Problem, Source Quench, Redirect, Echo, Echo Reply, Timestamp, Information Request, Information Reply, Address Request, and Address Reply? A. ICMP B. UDP C. TCP D. TFTP E. FTP

2 Answers   TCP,

---

take a pen and copy before solving that question there is a router name Ra there is two switch sw1 and sw2 sw1 is coneceted through fa0/1 interface of router Ra sw2 is conected through the fa1/1 serai interface of router s0/1 conected through the isp with it ip address 192.168.1.1 now therer are three host conexted through the sw1 and having ip host1=10.1.2.1 host2=10.1.2.2 host3=10.1.2.3 now there is also 3ree host conected through switch 2 i.e sw2 having ip host4=10.1.1.1 host 5=10.1.1.2 host 6=10.1.1.3 now i think u have made corect confrigation.now questios is started network admin configure the Ra router in that fassion Ra(config)#access-list 2 permit 10.1.1.0 0.0.0.255 Ra(config)#line vty 0 4 ra(config)#access-class 2 in now question is that why should network admnistratoe do it in this maneer A to give access sw1 host to acess internet B to prevent sw1 host from acessing comand promt c to prevent sw2 host from accessing console of router ra D to give sw2 host access to the enternet e prevent sw1 host from accessing internet f to prevent sw1 host from acessing the sw2 host network isp------(s0/1)..RA..(fa1/1)---SW2-host (4,5,6) | | (sw1)------host 1,2,3 this is not exect digarm but help to derive the diagram plz answer as soon as possible

6 Answers   AT&T,

---

Which of the following can reply to a Novell Get Nearest Server (GNS) request? A.) Local Novell server B.) Remote Novell Printer C.) Cisco router D.) Novell client

1 Answers  

---

What is VLSM ?

5 Answers   HCL,

---

Which layer of the 7 layer model provides services to the Application layer over the Session layer connection? A.) Transport B.) Application C.) Session D.) Network E.) Datalink F.) Presentation

2 Answers   CTS,

---

What is required to support full-duplex Ethernet? A.) Multiple paths between multiple stations on a link B.) Automatic sensing operation by all connected stations C.) Loopback and collision detection disabled D.) Full-duplex NIC cards

1 Answers  

---

Your Ethernet interface currently has the IP address of 1.1.1.1/24. You would like it to have a second IP address of 2.2.2.2/24. Which command will do that? A.) ip address 1.1.1.1 2.2.2.2 255.255.255.0 B.) ip address 2.2.2.2 255.255.255.0 secondary C.) ip address 2.2.2.2 255.255.255.0 D.) This cannot be done, you can only have 1 IP address per physical interface. E.) ip address 2.2.2.2 /24

1 Answers  

---

Which protocols are link states?

0 Answers  

---

hi friends i donot know this is the networking question or not but if you help me then i will thankfull to you the problem is like that in my comnay there are 200 user which log one at a time now only one user is not able to get the dhcp address and othr are geting the dhcp my company sys admin is saying that this is the n/w fault while i am saying that this is not the n/w fault for the cleaerfication of my side i take a straight workng cable and connect that user directly to my cisco 24port switch now problem is stiil like that but one thing i wan to say he is geting manually ip and able to access internet he is able to ping the server but whrnever he tyeme \\<ip address of server> error comes like networl path provided not accepted by provider some thing like that. my systm admin is saying that i have o do somthing on my firewall but i am saying that no issue with firewall in that i connect my latop to the spefic port from where the user is conected then i am geting dhcp ip address and i am able to connect the server also i donot know why this is happen my syadmin is senior to me so i canot blame him plz help e what to do i am very weak in the filed of systym jitendera kumar sinha

6 Answers  

---