What is the purpose of Split Horizon?
A.) It prevents the regular update messages from reinstating
a route
that has gone down
B.) Information received on an interface cannot be sent back
out the
same interface
C.) Informs all neighbor routers that two routes exist
D.) Tells the router the destination is unreachable
- 1 Answers
- 4320 Views
- I also Faced
- E-Mail Answers
Answer / guest
Answer: B
Split Horizon - If you learn a protocol?s route on an
interface, do not
send information about that route back out that interface.
| Is This Answer Correct ? | 2 Yes | 0 No |
hi... i am usin packet tracer 5.0.. i hav connect two routers A and B. A has 200.100.25.100 and 1.0.0.1 and router B has 200.100.50.100 and 1.0.0.2... i hav connected 1.0.0.1 and 1.0.0.2... now i want to route 200.100.25.100 and 200.10.50.100 usin rip.. i enable rip in both the routers... but whn i give the command show ip route... i jus get this Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set A# so can sombody tell me where i hav gone wrong... thanku
What is the command for change serial cost?
Mention what does the clock rate do?
What are segments?
What requirements should a VPN fulfill?
Explain what is eigrp?
What are the advantages of a layered model in the networking industry?
what is the major difference between EIGRP & IGRP?
take a pen and copy before solving that question there is a router name Ra there is two switch sw1 and sw2 sw1 is coneceted through fa0/1 interface of router Ra sw2 is conected through the fa1/1 serai interface of router s0/1 conected through the isp with it ip address 192.168.1.1 now therer are three host conexted through the sw1 and having ip host1=10.1.2.1 host2=10.1.2.2 host3=10.1.2.3 now there is also 3ree host conected through switch 2 i.e sw2 having ip host4=10.1.1.1 host 5=10.1.1.2 host 6=10.1.1.3 now i think u have made corect confrigation.now questios is started network admin configure the Ra router in that fassion Ra(config)#access-list 2 permit 10.1.1.0 0.0.0.255 Ra(config)#line vty 0 4 ra(config)#access-class 2 in now question is that why should network admnistratoe do it in this maneer A to give access sw1 host to acess internet B to prevent sw1 host from acessing comand promt c to prevent sw2 host from accessing console of router ra D to give sw2 host access to the enternet e prevent sw1 host from accessing internet f to prevent sw1 host from acessing the sw2 host network isp------(s0/1)..RA..(fa1/1)---SW2-host (4,5,6) | | (sw1)------host 1,2,3 this is not exect digarm but help to derive the diagram plz answer as soon as possible
What cable called v.35?
Identify the command that saves the configuration stored in RAM to NVRAM? A.) copy running-config startup-config B.) copy tftp running-config C.) copy startup running D.) copy active to backup
If bandwidth will increase what will happen?
CCNA 
