Answer / guest

Answer: B C D

Autonomous system must be interconnected, assigned the same
AS # and

configured with the same routing protocol.

Can you explain the difference between trusted and untrusted networks?

2 Answers   CCIE, Wipro,

---

Hi Guys I am facing one problem while configuring PAP over Point to Point links. Configuration scenario is like this. ROUTER 1: (Hostname – R1) R1(config)#username R2 password CCNA2 R1(config)#interface serial 1/1 R1(config-if)ip address 10.0.0.1 255.0.0.0 R1(config-if)#lock rate 64000 R1(config-if)#encapsulation ppp R1(config-if)#ppp authentication pap R1(config-if)#ppp pap sent –username R1 password CCNA1 R1(config-if)#no shutdown ROUTER 2: (Hostname – R2) R2(config)#usename R1 password CCNA1 R2(config)#interface serial 1/1 R2(config-if)#ip address 10.0.0.2 255.0.0.0 R2(config-if)#encapsulation ppp R2(config-if)# ppp authentication pap R2(config-if)# ppp pap sent –username R2 password CCNA2 R2(config-if)#no shutdown Now problem is that, after configure the command “ppp authentication pap” the “Line protocol” status goes down on each router. But when I disable this command using “no ppp authentication pap”, the “Line Protocol” status goes up. What could be the problem, can anyone explain it plzzz….!!! Thanks in Advance…!! Shahin..

6 Answers  

---

What command do we give if router ios is stucked?

0 Answers  

---

In eigrp metric parameters which 2 options are enable by default?

0 Answers  

---

Given an IPX network with redundant paths, what command will configure load balancing? A.) ipx load-balance B.) ip maximum-paths 2 C.) ipx maximum-paths 2 D.) ipx load-share

2 Answers  

---

For IPX, what is the DEFAULT Cisco Encapsulation on an Ethernet interface? A.) novell-ether B.) gns C.) snap D.) arpa E.) sap F.) dix

1 Answers  

---

why we give clock rate to DCE and not to DTE what is the difference in the two.

3 Answers  

---

hello friend i have answerd more time of your question or doute.now i am seeing towards you for help,plz send the soln before monedya the problem is i have three router r1 and r2 and r3 they are conested in that maneer thai is r1---r2---r3---server | | server bothe server have diffrent ip now i have to implemnt access list on the r3 router in such a way that user from r1 can access only one server while user from r2 can access whole servre i ahve done it but both user of r1 and r2 uses all server i need help please help me this time? i have repalsced my firwall by r3 router so bacicaly i have to implement it on my firewall but you tell me on cisco router please help

2 Answers  

---

How many LMI types are available on Cisco routers? A.) Four B.) Two C.) Five D.) Three

3 Answers  

---

What is a back off on an 802.3 networks? A. It is latency in store and forward switching B. It is the time used for token passing from machine to machine C. It is the retransmission delay that is enforced when a collision occurs D. It is the result of two nodes transmitting at the same time. The frames from each transmitting device collide and are damaged

1 Answers  

---

How are straight and crossable cables different from each other?

0 Answers  

---

What is the Difference between Switch and Bridge?

9 Answers  

---