Answer / dude

man were you drunk when you were writing this? i cant stop
myself laughing out loud..

Answer / raj

hi friend frist you chek your cisco spelling and your
leaving in ahmedabad why this ok

Answer / dharmendra soni

hey don,t worry

If you want more information about cisco,no problem
you go ahead cisco sit. First go google then type
which need to you.

Answer / ritu nasa

Do CCNA,CCNP or CCIE like courses.......which will help you
out.

Answer / dharmendra kumar soni

Dear,
No problem you can do it but if you going to ccna then be
care full you must have basic knowledge of ccna then u would
be next ccna security or ccna voice,bcz ccna is not enough
for us...........if u getting any more information then go
to goolge search and type what require u.......



Thanks

D.Soni

Answer / gtech

I have answer : Z Y X W V U T S
R Q P O N M
L K J I H G
F E D C B A
once you wright these letters in right order...you will get
the answer... :D

What is required to support full-duplex Ethernet? A.) Multiple paths between multiple stations on a link B.) Automatic sensing operation by all connected stations C.) Loopback and collision detection disabled D.) Full-duplex NIC cards

1 Answers  

Given the following IP address from the Class C address range 192.168.21.12. Your network plan needs addresses for 28 small prkps Each office uses its own shored. The network design specifies that you confound for five bits of subnetting. When you confound for this in Cisco IOS software which shored mask should you use? A. 255.255.0.28 B. 255.255.255.0 C. 255.255.255.28 D. 255.255.255.248 E. 255.255.255.252

1 Answers  

Identify 1 characteristic of RARP? A.) MAC to IP address translation B.) Connectionless delivery of packets C.) Can be used to initiate remote O/S load sequence D.) Generates error and control messages

5 Answers  

Cisco routers use wildcard masking to identify how to check or ignore corresponding IP address bits. What does setting a wildcard mask bit to 0 cause the router to do? A. It tells the router to check the corresponding bit value. B. It tells the router to ignore the corresponding bit value. C. It tells the router to check its alternate routing list. D. It tells the router to use its primary routing list.

2 Answers  

In distance-vector routing, there is a problem known as the 'count to infinity' problem. What is the most direct solution to this? A.) Defining a Maximum. B.) You can not solve the 'count to infinity' problem with a distance vector protocol. C.) Poison Reverse. D.) Triggered Updates. E.) Split Horizon.

2 Answers  

What is the name of best path in eigrp protocol?

0 Answers  

If you are in IOS user mode, which command do you use to enter the privileged mode? A. Set B. Enable C. Configure D. Privileges

2 Answers  

Identify the OSI layer associated with bits? A.) Physical B.) Network C.) Binary D.) Data link

2 Answers  

Novell IPX network addresses have two conferrable parts. The network administrator specifies the IPX network number. How is the node number determined? A. It is the serial number of the given device B. It is assigned as a lease by Novell DHCP C. It is also set by the network administrator D. It is usually the MAC address of one Interface E. It is downloaded by Netware Core Protocol (NCP)

1 Answers  

what is a malicious router?when it occurs? what is a malicious pacekt ?when it occurs?

1 Answers  

Of the following switching types, which one has the lowest latency? A.) Cut-through B.) Fragment Free C.) None D.) Store-and-forward

1 Answers  

Identify the command to configure the router to boot from an IOS located on a TFTP server? A.) boot system tftp IOS.exe 172.16.5.1 B.) boot system tftp 172.16.5.1 IOS.exe C.) boot system flash tftp 172.16.5.1 D.) boot system IOS.exe 172.16.5.1

2 Answers   HCL,