Mechanical Engineering Interview Questions
Questions Answers Views Company eMail

What are the causes of positive and negative propeller slip?

RRB,

1697

What will be the cause of scavenging fire?

RRB,

1679

What will you do when scavenge fire happened?

RRB,

1585

"What do you going to observe, when a diesel engine is running?"

RRB,

1513

Where is the expansion tank located?

RRB,

1693

How the F.W.C. system of diesel engine circulate?

RRB,

1749

What is mean effective press?

RRB,

1729

Draw a crankshaft and show the parts?

RRB,

1813

What is the lower part of connecting rod?

RRB,

2 4011

What should you do before you start the engine?

NSPCL, RRB,

1817

"When you will install a new piston ring, what will be the position of it?"

RRB,

1526

What is max pressure?

RRB,

2086

What are the things to do when approaching the port?

RRB,

1627

What will be the cause of the loose compression in a cylinder?

RRB,

1 2679

What is the maximum P-max for a cylinder in M/E.

RRB,

1728


Post New Mechanical Engineering Questions

Un-Answered Questions { Mechanical Engineering }

Where pneumatic system is used?

725


Describe How much Record maintain store Keeper and Write use of the Records?

1690


how to prepare welding procedure specification and pqr

4713


i require technical question paper which has been asked in last railway recruitment board exam for the post of junior engr.

1694


Explain how are the pneumatic system and the hydraulic system similar?

730






What are the causes of positive and negative propeller slip?

3567


What is the use of center punch?

880


Define a process flow diagram?

752


IF RPM OF PTO OF TRACTOR IS 540,torque at pto is 21kg/cm sq.& WE NEED IT TO 1800 RPM ,THROUGH GEAR ONLY FOR THAT WHAT WOULD BE ETHE GEAR STRUCTURE( I.E.NO TEETH OF BOTH GEAR ) IN ORDER TO GET 1800 RPM OUTPUT.

1955


When repacking a valve the rings of packing should be oriented so that the packing ends are installed ____________.

1953


what is punching force required for embossing of depth 3.5mm and diameter 58mm

1802


I need BHEL Engineer Trainee written test papers in Mechanical stream.

1952


What is the purpose of air blow?

1579


State fourier’s law of conduction.

804


2. Dry saturated steam at 3.5 bar is expanded through a convergent nozzle to 2.2 bar. The exit area is 5 sq. cm. Calculate the exit velocity and mass flow rate, assuming isentropic expansion and super saturated flow. b) A cast iron cylinder head is fastened to a cylinder of 750mm bore with 12 stud bolts. The maximum pressure inside the cylinder is 3 Mpa. The stiffness of part is thrice the stiffness of the bolt. What should be the initial tightening load so that the point is leak proof at maximum pressure? Also choose a suitable bolt for the above application 2 The propeller shaft of a marine engine is to transmit 600 kW at 1200 rpm, without a significant bending. The efficiency of the propeller is 88% at 32 knots ( 1 knot = 1085 km/hr). If the slenderness ratio is less than 50 and the permissible shear stress should not exceed 65 Mpa. Determine the diameter of shaft. 3 A semi-elliptic leaf spring consists of two extra full-length leaves and six graduated length leaves, including the master leaf. Each leaf is 7.2 mm thick and 65 mm wide. The centre-to-centre distance between the two eyes is 1.3m. The leaves are pre-stressed in such a way that when the load is maximum, stress induced in all leaves are equal to 380 N/mm sq. Determine the maximum force that the spring can withstand

1918