Interested to Buy Any Domain ? << Click Here >> for more details...
What is meant by transformer, why it should be used, with
out that equipment what happens if we transformed the
supply?
- 12 Answers
- 26902 Views
- Bhel, I also Faced
- E-Mail Answers
Answer Posted / panks
Transformer is that stactic device which transfers power
from one ckt. to other w/o changing frequency.
Transformer is used for stepping up & down the voltage
levels or as per requirments whenever needed.
Voltage level should be lower for Consumers like
Industries, Domestic, etc as compared to Generating
stations, Substations, switchyards hence w/o Trafo, voltage
level can't be changed like stepping up or down, hence to
get desired voltage level, we have to use transformers.
| Is This Answer Correct ? | 7 Yes | 4 No |
Post New Answer View All Answers
Dear all, I just want to ask an expert on this forum for some insights. For the magnetic balance test, when applied voltage on a Delta-Star transformer e.g. Dyn11, the following relationships apply for HV side: 1. H1-H2 = H2-H3 H3-H1 2. H2-H3 = H3-H1 H1-H2 3. H3-H1 = H1-H2 H2-H3 For the LV side also: 4. X1-X0 = X2-X0 X3-X0 5. X2-X0 = X3-X0 X1-X0 6. X3-X0 = X1-X0 X2-X0 Is there a similar pattern for Y-d, Y-Y, D-d? And how about Y-z, D-z, Z-y transformers? I've tested a YNzn5 transformer and for LV side I don't see the pattern. In this particular case I got for LV side the following (see values below): H1-H0 H2-H0 H3-H0 X0-X1 X0-X2 X0-X3 128.0 119.9 7.2 29.2 13.3 15.8 70.7 128.4 59.2 23.4 22.0 3.6 7.2 120.1 128.1 13.4 29.3 15.8 What is the relationship here for LV? For row 1 I see the relationship, for row 3 I also see but it's shifted, but for row 2 I don't see such relationship. Any suggestions, answers, someone?
What is power factor why we should maintain the power factor unless what will happen
how we decide wire gauge for ac or dc coil and what is the basic diff. B/w these two coil?
Dear all, I want to use Induction motor to open and close a 1 ton door. How much power do I need. Thanks
7- What is the Dissipation Factor and the difference between it and Insulation Resistance Test? 8- What is the task (function) of DC and AC reactors in power plant? 9- What is the task (function) of (open delta with earthed) in some types in transformers? 10- What is the base of the selection of the vector group in transformers? 11- What is the zig-zag transformer and its function by drawing in large detail? 12- What is the polarity ? 13- Why we make short between phase(R) in high side and phase (r) in low side in vector group test? Where High Side ( R ,S and T ) and Low Side ( r ,s and t ). 14- What are the time on delay and time off delay? 15- What is the vector group? 15- What is the task (function) of different types of vector group such as Dyn11 , Dd0 , YNd1,……..,?
If Dg set load increase 25%, How much increase fuel Consumption (15 kva 2 cylinder DG set)
What's mean HVF & HAF in Vacuum Circuit Breaker?
how copper and aluminium wires or cables are choose for current rating? please provide copper and aluminium wire selection chart for different current rating ?
I need HT sphere gap calibration table. Can any body help me.
Can anybody please refer the best and simple book for about Protection relays and in detail of all its protection ?
Ceiling Fan and Storage type water heater. Discuss
what is the safety points of vaccum circuit breaker.
I want d.g.set our company
Earth is a conductor or load?then ammeter connect to 3- phase supply,it shows the measurents or not?
What is the efficiency during maximum power transfer?
