Interested to Buy Any Domain ? << Click Here >> for more details...
Suppose there are two cylinders / vessels.In one cylinder
the pressure is 1.5 bar & in other 0.5 bar.If both cylinder
are connected internally through valve connection, what
will be the final pressure in both?
- 19 Answers
- 25520 Views
- BARC, Bhel, HPCL, I also Faced
- E-Mail Answers
Answer Posted / raghu
I think it depends upon the volume of the two vessels.
if the two vessels are having same volume then final
pressure may be 0.866 bar
| Is This Answer Correct ? | 4 Yes | 8 No |
Post New Answer View All Answers
Discuss venturimeter?
How do you control cylinder liner wear?
What is the pressure of fuel oil on main engine and diesel generator?
Write down the equation for conduction of heat through a slab or plane wall.
What are two essential conditions of perfect gas ?
What is the purpose of air blow?
why do u ant to join the indian army??
How does turbine work?
Why is thick steel wire stronger than thin steel wire?
What is the microstructure content of D25-8 nodular cast iron?
what are various part found in vapour absorption machine and its working
1. What are good characteristics of good combustion in a boiler? 2. What do you analyze from boiler water analysis? 3. What do you treat in high alkalinity of boiler water? 4. What is a feed water pump? Dearator feed heater? 5. What is the purpose of the nozzle of impulse turbine? 6. What are the things needed to have an efficient boiler burning? 7. Name Of Parts And Each Purpose 8. What are the causes of emergency stop in a steam engine? 9. What is the normal vacuum pressure in a steam turbine atmospheric condenser? What would cause the press to falls? 10. Steam turbine (function an parts) 11. What is the boiling point of water? 12. What are the safety devices of boiler? 13. What is the effect of high alkaline water to a boiler? 14. Steps In starting boilers. 15. Small gear found in the steam turbine. 16. What is an Economizer? 17. What are the methods of heat transfer? 18. Types of pressure 19. What are the different parts of impulse reaction turbine? 20. What is the color of the flame of the boiler running in good condition? 21. What type of pump is commonly used is feed water system in auxiliary boiler? 22. What is the specific heat of water? 23. What do you do to prevent flare black? 24. What is a brake horsepower? 25. What is the purpose of a de-superheater? 26. What is the purpose of corrugated furnaces? 27. What are the causes of steam turbine failure? 28. What is the purpose of superheater? 29. Given a cutaway isometric view of the steam turbine. Examinee was asked to identify the following Parts: 30. What is thrust bearing? 31. Give five boiler mounting valves. 32. In steam boiler, what are the various test in water boiler? 33. How much calorific value of heat is needed to heat 00c of 34. What will happen if boiler backfires? 35. What is the color of flame if the boiler is running in good condition? How about when it is not in good condition? 36. How does the steam work in a steam turbine? 37. What are the causes of boiler backfire and steps in how to prevent it from happening? 38. What are the causes of high alkalinity in boiler water? 39. What are sensible heat, latent heat, and specific heat of water? 40. What are the causes of turbine vibration 41. Identify the parts of steam turbine 42. What is the normal Ph value of boiler water 43. Causes of dilution of lubricating oil in a steam turbine? 44. Explain briefly- good combustion of auxiliary boiler? 45. Method of testing or checking boiler water? 46. What is mean carry over of Aux. Boiler? 47. What are steam turbine parts usually come into damage? 48. Why must we pay attention when we drain steam in steam turbine. What factors are observed? 49. What type of pump use in boiler F.O. system? 50. What parameters to be reported when we send lubricating oil for shore analysis? 51. In boiler, what does steam and smoke goes out to the funnel. What reason? 52. Where can you find the feed check valve and feed stop valve and give the purpose of it? 53. What are the causes of troubles in boiler during operations? 54. Give the purpose of nozzle in impulse turbine? 55. What s gland sealing steam? 56. How to prevent back fire of boiler? 57. What is the used of economizer in boiler? 58. What is the seal packing gland for turbine? 59. What is the flow of steam in an impulse turbine? 60. What will happen if you blow the soot in the boiler? 61. State the purpose of air heater? 62. How to operate soot blower boiler and economizer? 63. What do you mean by A.CC.? 64. What is the thermal efficiency of a diesel engine? 65. What is a blow down valves?
How pipe flanges are electrically insulated?
When a 30KW/3 ph pump runs one hour continously, what will be the heat dissipated? how can i find this, any general equation?
hii sir. how will CAE/CFD courses useful to B.tech freshers? is this courses useful to getting job in automobile industry? plz give rply..
